2.4 A spherical conductor of radius 12 cm has a charge of 1.6 × 10–7C distributed uniformly on its surface. What is the electric field (a) inside the sphere (b) just outside the sphere (c) at a point 18 cm from the centre of the sphere?

5.8 THE CONSERVATION OF MECHANICAL a ball of mass m being dropped from a cliff of ENERGY height H. For simplicity we demonstrate this important principle for one-dimensional motion. Suppose that a body undergoes displacement ∆x under the action of a conservative force F. Then from the WE theorem we have, ∆K = F(x) ∆x If the force is conservative, the potential energy function V(x) can be defined such that − ∆V = F(x) ∆x The above equations imply that Fig. 5.5 The conversion of potential energy to kinetic ∆K + ∆V = 0 energy for a ball of mass m dropped from a ∆(K + V ) = 0 (5.10) height H. Reprint 2025-26 WORK, ENERGY AND POWER 79 The total mechanical energies E0, Eh, and EH Answer (i) There are two external forces on of the ball at the indicated heights zero (ground the bob : gravity and the tension (T ) in the level), h and H, are string. The latter does no work since the displacement of the bob is always normal to the EH = mgH (5.11 a) string. The potential energy of the bob is thus 1 2 E h = mgh + mv h (5.11 b) associated with the gravitational force only. The 2 2 total mechanical energy E of the system is E0 = (1/2) mvf (5.11 c) conserved. We take the potential energy of the The constant force is a special case of a spatially system to be zero at the lowest point A. Thus, dependent force F(x). Hence, the mechanical at A : energy is conserved. Thus EH = E0 1 2 1 2 E = mv0 (5.12) or, mgH = mv f 2 2 v f = 2 gH [Newton’s Second Law] a result that was obtained in section 5.7 for a where TA is the tension in the string at A. At thefreely falling body. highest point C, the string slackens, as the Further, tension in the string (TC) becomes zero. EH = Eh Thus, at Cwhich implies, 2 1 2 v h = 2 g(H − h) (5.11 d) E = mv c + 2mgL (5.13) 2 and is a familiar result from kinematics. At the height H, the energy is purely potential. mvc2It is partially converted to kinetic at height h and mg = [Newton’s Second Law] (5.14) L is fully kinetic at ground level. This illustrates the conservation of mechanical energy. where vC is the speed at C. From Eqs. (5.13) ⊳ and (5.14) Example 5.7 A bob of mass m is suspended 5 by a light string of length L . It is imparted a E = mgL horizontal velocity vo at the lowest point A 2 such that it completes a semi-circular Equating this to the energy at A trajectory in the vertical plane with the string 5 m 2 becoming slack only on reaching the topmost mgL = v 0 point, C. This is shown in Fig. 5.6. Obtain an 2 2 expression for (i) vo; (ii) the speeds at points or, v 0 = 5 gL B and C; (iii) the ratio of the kinetic energies (ii) It is clear from Eq. (5.14) (KB/KC) at B and C. Comment on the nature of the trajectory of the bob after it reaches vC = gL the point C. At B, the energy is 1 2 E = mv B + mgL 2 Equating this to the energy at A and employing the result from (i), namely v 02 = 5 gL , 1 2 1 2 mv B + mgL = mv 0 2 2 5 = m g L Fig. 5.6 2 Reprint 2025-26 80 PHYSICS ∴ vB = 3 gL k x m2 W = + (5.16) 2 (iii) The ratio of the kinetic energies at B and C is : 1 2 mv B K B 2 3 = = 2 1 K C 1 mvC 2 At point C, the string becomes slack and the velocity of the bob is horizontal and to the left. If the connecting string is cut at this instant, the bob will execute a projectile motion with horizontal projection akin to a rock kicked horizontally from the edge of a cliff. Otherwise the bob will continue on its circular path and complete the revolution. ⊳

8.2 STRESS AND STRAIN forces are applied parallel to the cross-sectional When forces are applied on a body in such a area of the cylinder, as shown in Fig. 8.1(b), manner that the body is still in static equilibrium, there is relative displacement between the it is deformed to a small or large extent depending opposite faces of the cylinder. The restoring force upon the nature of the material of the body and per unit area developed due to the applied the magnitude of the deforming force. The tangential force is known as tangential or deformation may not be noticeable visually in shearing stress. many materials but it is there. When a body is As a result of applied tangential force, there subjected to a deforming force, a restoring force is a relative displacement ∆x between opposite is developed in the body. This restoring force is faces of the cylinder as shown in the Fig. 8.1(b). equal in magnitude but opposite in direction to The strain so produced is known as shearing the applied force. The restoring force per unit area strain and it is defined as the ratio of relative is known as stress. If F is the force applied normal displacement of the faces ∆x to the length of the to the cross–section and A is the area of cross cylinder L. section of the body, ∆x Magnitude of the stress = F/A (8.1) Shearing strain = = tan θ (8.3) L The SI unit of stress is N m–2 or pascal (Pa) and its dimensional formula is [ ML–1T–2 ]. where θ is the angular displacement of the There are three ways in which a solid may cylinder from the vertical (original position of the change its dimensions when an external force cylinder). Usually θ is very small, tan θ acts on it. These are shown in Fig. 8.1. In is nearly equal to angle θ, (if θ = 10°, for Fig.8.1(a), a cylinder is stretched by two equal example, there is only 1% difference between θ forces applied normal to its cross-sectional area. and tan θ). The restoring force per unit area in this case is It can also be visualised, when a book is called tensile stress. If the cylinder is pressed with the hand and pushed horizontally, compressed under the action of applied forces, as shown in Fig. 8.2 (c). the restoring force per unit area is known as Thus, shearing strain = tan θ ≈ θ (8.4) compressive stress. Tensile or compressive In Fig. 8.1 (d), a solid sphere placed in the fluid stress can also be termed as longitudinal stress. under high pressure is compressed uniformly on In both the cases, there is a change in the all sides. The force applied by the fluid acts in length of the cylinder. The change in the length perpendicular direction at each point of the ∆L to the original length L of the body (cylinder surface and the body is said to be under in this case) is known as longitudinal strain. hydraulic compression. This leads to decrease (a) (b) (c) (d) Fig. 8.1 (a) A cylindrical body under tensile stress elongates by ∆L (b) Shearing stress on a cylinder deforming it by an angle θ(c) A body subjected to shearing stress (d) A solid body under a stress normal to the surface at every point (hydraulic stress). The volumetric strain is ∆V/V, but there is no change in shape. Reprint 2025-26 MECHANICAL PROPERTIES OF SOLIDS 169 in its volume without any change of its compression and shear stress may also be geometrical shape. obtained. The stress-strain curves vary from The body develops internal restoring forces material to material. These curves help us to that are equal and opposite to the forces applied understand how a given material deforms with by the fluid (the body restores its original shape increasing loads. From the graph, we can see and size when taken out from the fluid). The that in the region between O to A, the curve is internal restoring force per unit area in this case linear. In this region, Hooke’s law is obeyed. is known as hydraulic stress and in magnitude The body regains its original dimensions when is equal to the hydraulic pressure (applied force the applied force is removed. In this region, the per unit area). solid behaves as an elastic body. The strain produced by a hydraulic pressure is called volume strain and is defined as the ratio of change in volume (∆V) to the original volume (V). ∆V Volume strain = (8.5) V Since the strain is a ratio of change in dimension to the original dimension, it has no units or dimensional formula.