4.5 What is the magnitude of magnetic force per unit length on a wire carrying a current of 8 A and making an angle of 30º with the direction of a uniform magnetic field of 0.15 T?

4.6 A 3.0 cm wire carrying a current of 10 A is placed inside a solenoid perpendicular to its axis. The magnetic field inside the solenoid is given to be 0.27 T. What is the magnetic force on the wire?

8.2 STRESS AND STRAIN forces are applied parallel to the cross-sectional When forces are applied on a body in such a area of the cylinder, as shown in Fig. 8.1(b), manner that the body is still in static equilibrium, there is relative displacement between the it is deformed to a small or large extent depending opposite faces of the cylinder. The restoring force upon the nature of the material of the body and per unit area developed due to the applied the magnitude of the deforming force. The tangential force is known as tangential or deformation may not be noticeable visually in shearing stress. many materials but it is there. When a body is As a result of applied tangential force, there subjected to a deforming force, a restoring force is a relative displacement ∆x between opposite is developed in the body. This restoring force is faces of the cylinder as shown in the Fig. 8.1(b). equal in magnitude but opposite in direction to The strain so produced is known as shearing the applied force. The restoring force per unit area strain and it is defined as the ratio of relative is known as stress. If F is the force applied normal displacement of the faces ∆x to the length of the to the cross–section and A is the area of cross cylinder L. section of the body, ∆x Magnitude of the stress = F/A (8.1) Shearing strain = = tan θ (8.3) L The SI unit of stress is N m–2 or pascal (Pa) and its dimensional formula is [ ML–1T–2 ]. where θ is the angular displacement of the There are three ways in which a solid may cylinder from the vertical (original position of the change its dimensions when an external force cylinder). Usually θ is very small, tan θ acts on it. These are shown in Fig. 8.1. In is nearly equal to angle θ, (if θ = 10°, for Fig.8.1(a), a cylinder is stretched by two equal example, there is only 1% difference between θ forces applied normal to its cross-sectional area. and tan θ). The restoring force per unit area in this case is It can also be visualised, when a book is called tensile stress. If the cylinder is pressed with the hand and pushed horizontally, compressed under the action of applied forces, as shown in Fig. 8.2 (c). the restoring force per unit area is known as Thus, shearing strain = tan θ ≈ θ (8.4) compressive stress. Tensile or compressive In Fig. 8.1 (d), a solid sphere placed in the fluid stress can also be termed as longitudinal stress. under high pressure is compressed uniformly on In both the cases, there is a change in the all sides. The force applied by the fluid acts in length of the cylinder. The change in the length perpendicular direction at each point of the ∆L to the original length L of the body (cylinder surface and the body is said to be under in this case) is known as longitudinal strain. hydraulic compression. This leads to decrease (a) (b) (c) (d) Fig. 8.1 (a) A cylindrical body under tensile stress elongates by ∆L (b) Shearing stress on a cylinder deforming it by an angle θ(c) A body subjected to shearing stress (d) A solid body under a stress normal to the surface at every point (hydraulic stress). The volumetric strain is ∆V/V, but there is no change in shape. Reprint 2025-26 MECHANICAL PROPERTIES OF SOLIDS 169 in its volume without any change of its compression and shear stress may also be geometrical shape. obtained. The stress-strain curves vary from The body develops internal restoring forces material to material. These curves help us to that are equal and opposite to the forces applied understand how a given material deforms with by the fluid (the body restores its original shape increasing loads. From the graph, we can see and size when taken out from the fluid). The that in the region between O to A, the curve is internal restoring force per unit area in this case linear. In this region, Hooke’s law is obeyed. is known as hydraulic stress and in magnitude The body regains its original dimensions when is equal to the hydraulic pressure (applied force the applied force is removed. In this region, the per unit area). solid behaves as an elastic body. The strain produced by a hydraulic pressure is called volume strain and is defined as the ratio of change in volume (∆V) to the original volume (V). ∆V Volume strain = (8.5) V Since the strain is a ratio of change in dimension to the original dimension, it has no units or dimensional formula.