2.2 INSTANTANEOUS VELOCITY AND SPEED The average velocity tells us how fast an object has been moving over a given time interval but does not tell us how fast it moves at different instants of time during that interval. For this, we define instantaneous velocity or simply velocity v at an instant t. The velocity at an instant is defined as the limit of the average velocity as the time interval ∆t becomes infinitesimally small. In other words, ∆ x v = lim (2.1a) ∆ t → 0 ∆ t Fig. 2.1 Determining velocity from position-time d x = (2.1b) graph. Velocity at t = 4 s is the slope of the dt tangent to the graph at that instant. lim where the symbol stands for the operation ∆→t 0 Now, we decrease the value of ∆t from 2 s to 1 of taking limit as ∆tg0 of the quantity on its s. Then line P1P2 becomes Q1Q2 and its slope right. In the language of calculus, the quantity gives the value of the average velocity over on the right hand side of Eq. (2.1a) is the the interval 3.5 s to 4.5 s. In the limit ∆t → 0, differential coefficient of x with respect to t and the line P1P2 becomes tangent to the position- d x time curve at the point P and the velocity at t is denoted by (see Appendix 2.1). It is the d t = 4 s is given by the slope of the tangent at rate of change of position with respect to time, that point. It is difficult to show this process graphically. But if we useat that instant. numerical method to obtain the value of We can use Eq. (2.1a) for obtaining the the velocity, the meaning of the limiting value of velocity at an instant either process becomes clear. For the graph shown graphically or numerically. Suppose that we in Fig. 2.1, x = 0.08 t3. Table 2.1 gives the want to obtain graphically the value of value of ∆x/∆t calculated for ∆t equal to 2.0 s, velocity at time t = 4 s (point P) for the motion 1.0 s, 0.5 s, 0.1 s and 0.01 s centred at t = of the car represented in Fig.2.1 calculation. 4.0 s. The second and third columns give theLet us take ∆t = 2 s centred at t = 4 s. Then, t  t    ∆ ∆by the definition of the average velocity, the t + t −     and t 2 = and the value of t1= 2 2slope of ( Fig. 2.1) gives the value of     line P1P2 average velocity over the interval 3 s to 5 s. fourth and the fifth columns give the ∆x Table 2.1 Limiting value of at t = 4 s ∆ t Reprint 2025-26 MOTION IN A STRAIGHT LINE 15 3 a + 16b – a – 4b corresponding values of x, i.e. x (t1) = 0.08 t1 = = 6.0 × b 2.0 -1 ⊳and x (t2) = 0.08 t23. The sixth column lists the = 6.0 × 2.5 =15 m s difference ∆x = x (t2) – x (t1) and the last column gives the ratio of ∆x and ∆t, i.e. the Note that for uniform motion, velocity is average velocity corresponding to the value the same as the average velocity at all of ∆t listed in the first column. instants. We see from Table 2.1 that as we decrease Instantaneous speed or simply speed is the the value of ∆t from 2.0 s to 0.010 s, the value of magnitude of velocity. For example, a velocity of the average velocity approaches the limiting + 24.0 m s–1 and a velocity of – 24.0 m s–1 — value 3.84 m s–1 which is the value of velocity at both have an associated speed of 24.0 m s-1. It should be noted that though average speed over dx t = 4.0 s, i.e. the value of at t = 4.0 s. In this a finite interval of time is greater or equal to the dt magnitude of the average velocity, manner, we can calculate velocity at each instantaneous speed at an instant is equal to instant for motion of the car. the magnitude of the instantaneous velocity at The graphical method for the determination that instant. Why so ? of the instantaneous velocity is always not a 2.3 ACCELERATIONconvenient method. For this, we must carefully plot the position–time graph and calculate the The velocity of an object, in general, changes value of average velocity as ∆t becomes smaller during its course of motion. How to describe and smaller. It is easier to calculate the value this change? Should it be described as the rate of velocity at different instants if we have data of change in velocity with distance or with of positions at different instants or exact time ? This was a problem even in Galileo’s expression for the position as a function of time. time. It was first thought that this change could Then, we calculate ∆x/∆t from the data for be described by the rate of change of velocity decreasing the value of ∆t and find the limiting with distance. But, through his studies of value as we have done in Table 2.1 or use motion of freely falling objects and motion of differential calculus for the given expression and objects on an inclined plane, Galileo concluded that the rate of change of velocity with time is dx calculate at different instants as done in a constant of motion for all objects in free fall. dt On the other hand, the change in velocity with the following example. distance is not constant – it decreases with the ⊳ increasing distance of fall. This led to the Example 2.1 The position of an object concept of acceleration as the rate of change moving along x-axis is given by x = a + bt2 of velocity with time. where a = 8.5 m, b = 2.5 m s–2 and t is The average acceleration a over a time interval measured in seconds. What is its velocity at is defined as the change of velocity divided by t = 0 s and t = 2.0 s. What is the average the time interval : velocity between t = 2.0 s and t = 4.0 s ? v 2 – v1 ∆v (2.2)Answer In notation of differential calculus, the a = = t 2 – t1 ∆tvelocity is where v2 and v1 are the instantaneous velocities dx d 2 -1 2b t = 5.0 t m s or simply velocities at time t2 and t1 . It is thev = = ( a + bt ) = dt dt average change of velocity per unit time. The SI At t = 0 s, v = 0 m s–1 and at t = 2.0 s, unit of acceleration is m s–2 . v = 10 m s-1 . On a plot of velocity versus time, the average acceleration is the slope of the straight line x ( 4.0 ) − x ( 2.0 )Average velocity = connecting the points corresponding to (v2, t2) 4.0 − 2.0 and (v1, t1). Reprint 2025-26 16 PHYSICS Instantaneous acceleration is defined in the (c) An object is moving in negative direction same way as the instantaneous velocity : with a negative acceleration. ∆v d v (d) An object is moving in positive direction lim a = = (2.3) till time t1, and then turns back with the d t ∆→ t 0 ∆ t same negative acceleration. The acceleration at an instant is the slope of the tangent to the v–t curve at that An interesting feature of a velocity-time instant. graph for any moving object is that the area Since velocity is a quantity having both under the curve represents the magnitude and direction, a change in displacement over a given time interval. A velocity may involve either or both of these general proof of this statement requires use of factors. Acceleration, therefore, may result calculus. We can, however, see that it is true from a change in speed (magnitude), a for the simple case of an object moving with change in direction or changes in both. Like constant velocity u. Its velocity-time graph is velocity, acceleration can also be positive, as shown in Fig. 2.4. negative or zero. Position-time graphs for motion with positive, negative and zero acceleration are shown in Figs. 2.4 (a), (b) and (c), respectively. Note that the graph curves upward for positive acceleration; downward for negative acceleration and it is a straight line for zero acceleration. Although acceleration can vary with time, our study in this chapter will be restricted to motion with constant acceleration. In this case, the average acceleration equals the constant value of acceleration during the interval. If the velocity of an object is vo at t = 0 and v at time t, we have v − v 0 a = or, v = v 0 + a t (2.4) t − 0 Fig. 2.3 Velocity–time graph for motions with Fig. 2.2 Position-time graph for motion with constant acceleration. (a) Motion in positive (a) positive acceleration; (b) negative direction with positive acceleration, acceleration, and (c) zero acceleration. (b) Motion in positive direction with Let us see how velocity-time graph looks like negative acceleration, (c) Motion in for some simple cases. Fig. 2.3 shows velocity- negative direction with negative acceleration, (d) Motion of an object withtime graph for motion with constant acceleration negative acceleration that changesfor the following cases : direction at time t1. Between times 0 to (a) An object is moving in a positive direction t1, it moves in positive x - direction with a positive acceleration. and between t1 and t2 it moves in the (b) An object is moving in positive direction opposite direction. with a negative acceleration. Reprint 2025-26 MOTION IN A STRAIGHT LINE 17 Fig. 2.4 Area under v–t curve equals displacement of the object over a given time interval. The v-t curve is a straight line parallel to the time axis and the area under it between t = 0 and t = T is the area of the rectangle of height u and base T. Therefore, area = u × T = uT which Fig. 2.5 Area under v-t curve for an object with is the displacement in this time interval. How uniform acceleration. come in this case an area is equal to a distance? Think! Note the dimensions of quantities on the two coordinate axes, and you will arrive at As explained in the previous section, the area the answer. under v-t curve represents the displacement. Therefore, the displacement x of the object is : Note that the x-t, v-t, and a-t graphs shown in several figures in this chapter have sharp 1 x = ( v – v 0 ) t + v 0 t (2.5)kinks at some points implying that the 2 functions are not differentiable at these But v − v 0 = a tpoints. In any realistic situation, the functions will be differentiable at all points 1 2 Therefore, x = a t + v 0 tand the graphs will be smooth. 2 What this means physically is that 1 2 or, x = v 0 t + at (2.6)acceleration and velocity cannot change 2 values abruptly at an instant. Changes are Equation (2.5) can also be written as always continuous. v + v 0 x = t = v t (2.7a)2.4 KINEMATIC EQUATIONS FOR 2 UNIFORMLY ACCELERATED MOTION where, For uniformly accelerated motion, we can derive some simple equations that relate displacement v + v 0 v = (constant acceleration only)(x), time taken (t), initial velocity (v0), final 2 velocity (v) and acceleration (a). Equation (2.4) (2.7b) already obtained gives a relation between final and initial velocities v and v0 of an object moving Equations (2.7a) and (2.7b) mean that the object with uniform acceleration a : has undergone displacement x with an average velocity equal to the arithmetic average of the v = v0 + at (2.4) initial and final velocities. From Eq. (2.4), t = (v – v0)/a. Substituting this in This relation is graphically represented in Fig. 2.5. Eq. (2.7a), we get The area under this curve is : Area between instants 0 and t = Area of triangle  v + v 0   v − v 0  v 2 − v 02 x = v t =ABC + Area of rectangle OACD  2   a = 2a 1 2 2 = (v – v 0 ) t + v 0 t v = v 0 + 2ax (2.8) 2 Reprint 2025-26 18 PHYSICS This equation can also be obtained by t v 0 + at ) d tsubstituting the value of t from Eq. (2.4) into Eq. = ∫ 0 ( (2.6). Thus, we have obtained three important equations : 1 2 x – x 0 = v 0 t + a t 2 v = v 0 + at 1 2 1 2 x = x 0 + v 0 t + a t x = v 0t + at 2 2 We can write v 2 = v 02 + 2ax (2.9a) d v d v d x d v a = = = v d t d x d t d x connecting five quantities v0, v, a, t and x. These or, v dv = a dxare kinematic equations of rectilinear motion for Integrating both sides,constant acceleration. The set of Eq. (2.9a) were obtained by v x v d v = a d xassuming that at t = 0, the position of the particle, ∫ v 0 ∫ x 0 x is 0. We can obtain a more general equation if we take the position coordinate at t = 0 as non- v 2 – v 02 = a ( x – x 0 ) zero, say x0. Then Eqs. (2.9a) are modified 2 (replacing x by x – x0 ) to : 2 2 v = v 0 + 2a ( x – x 0 ) v = v 0 + at The advantage of this method is that it can be used 1 2 for motion with non-uniform acceleration x = x 0 + v 0t + at (2.9b) also. 2 Now, we shall use these equations to some v 2 = v 02 + 2a ( x − x 0 ) (2.9c) important cases. ⊳ ⊳ ⊳ Example 2.3 A ball is thrown vertically Example 2.2 Obtain equations of motion upwards with a velocity of 20 m s–1 from for constant acceleration using method of the top of a multistorey building. The calculus. height of the point from where the ball is thrown is 25.0 m from the ground. (a) How high will the ball rise ? and (b) how longAnswer By definition will it be before the ball hits the ground? d v Take g = 10 m s–2. a = d t dv = a dt Answer (a) Let us take the y-axis in the Integrating both sides vertically upward direction with zero at the v t ∫ v 0 d v = ∫ 0 a d t ground, as shown in Fig. 2.6. Now vo = + 20 m s–1, t d t (a is a = – g = –10 m s–2, = a ∫ 0 v = 0 m s–1 constant) If the ball rises to height y from the point of v – v 0 = at launch, then using the equation 2 + 2 a 0 ( y – y 0 ) v = v 0 + at v 2 = v we get d x Further, v = 0 = (20)2 + 2(–10)(y – y0) d t Solving, we get, (y – y0) = 20 m. dx = v dt Integrating both sides (b) We can solve this part of the problem in two x t ways. Note carefully the methods used. ∫ x 0 dx = ∫v0 d t Reprint 2025-26 MOTION IN A STRAIGHT LINE 19 0 = 25 +20 t + (½) (-10) t2 Or, 5t2 – 20t – 25 = 0 Solving this quadratic equation for t, we get t = 5s Note that the second method is better since we do not have to worry about the path of the motion as the motion is under constant acceleration. ⊳ ⊳ Example 2.4 Free-fall : Discuss the motion of an object under free fall. Neglect air resistance. Answer An object released near the surface of the Earth is accelerated downward under the influence of the force of gravity. The magnitude of acceleration due to gravity is represented by g. If air resistance is neglected, the object is Fig. 2.6 said to be in free fall. If the height through which the object falls is small compared to the FIRST METHOD : In the first method, we split earth’s radius, g can be taken to be constant, the path in two parts : the upward motion (A to equal to 9.8 m s–2. Free fall is thus a case of B) and the downward motion (B to C) and motion with uniform acceleration. calculate the corresponding time taken t1 and We assume that the motion is in y-direction, t2. Since the velocity at B is zero, we have : more correctly in –y-direction because we v = vo + at choose upward direction as positive. Since the 0 = 20 – 10t1 acceleration due to gravity is always downward, Or, t1 = 2 s it is in the negative direction and we have This is the time in going from A to B. From B, or a = – g = – 9.8 m s–2 the point of the maximum height, the ball falls The object is released from rest at y = 0. Therefore, freely under the acceleration due to gravity. The v0 = 0 and the equations of motion become: ball is moving in negative y direction. We use v = 0 – g t = –9.8 t m s–1equation y = 0 – ½ g t2 = –4.9 t 2 m 1 2 y = y 0 + v 0t + at v2 = 0 – 2 g y = –19.6 y m2 s–2 2 These equations give the velocity and the We have, y0 = 45 m, y = 0, v0 = 0, a = – g = –10 m s–2 distance travelled as a function of time and also 0 = 45 + (½) (–10) t2 2 the variation of velocity with distance. The Solving, we get t2 = 3 s variation of acceleration, velocity, and distance, with time have been plotted in Fig. 2.7(a), (b)Therefore, the total time taken by the ball before and (c). it hits the ground = t1 + t2 = 2 s + 3 s = 5 s. SECOND METHOD : The total time taken can also be calculated by noting the coordinates of initial and final positions of the ball with respect to the origin chosen and using equation 1 2 y = y0 + v 0t + at 2 Now y0 = 25 m y = 0 m vo = 20 m s-1, a = –10m s–2, t = ? (a) Reprint 2025-26 20 PHYSICS traversed during successive intervals of time. Since initial velocity is zero, we have 2 y = −1 gt 2 Using this equation, we can calculate the position of the object after different time intervals, 0, τ, 2τ, 3τ… which are given in second column of Table 2.2. If we take (–1/ 2) gτ2 as y0 — the position coordinate after first time interval τ, then third column gives (b) the positions in the unit of yo. The fourth column gives the distances traversed in successive τs. We find that the distances are in the simple ratio 1: 3: 5: 7: 9: 11… as shown in the last column. This law was established by Galileo Galilei (1564-1642) who was the first to make quantitative studies of free fall. ⊳ ⊳ Example 2.6 Stopping distance of vehicles : When brakes are applied to a moving vehicle, the distance it travels before stopping is called stopping distance. It is (c) an important factor for road safety and depends on the initial velocity (v0) and theFig. 2.7 Motion of an object under free fall. braking capacity, or deceleration, –a that (a) Variation of acceleration with time. (b) Variation of velocity with time. is caused by the braking. Derive an (c) Variation of distance with time ⊳ expression for stopping distance of a vehicle in terms of vo and a. ⊳ Example 2.5 Galileo’s law of odd Answer Let the distance travelled by the vehicle numbers : “The distances traversed, during before it stops be ds. Then, using equation of equal intervals of time, by a body falling 2 motion v2 = vo + 2 ax, and noting that v = 0, we from rest, stand to one another in the same have the stopping distance ratio as the odd numbers beginning with unity [namely, 1: 3: 5: 7…...].” Prove it. – v 02 d s = 2aAnswer Let us divide the time interval of motion of an object under free fall into many Thus, the stopping distance is proportional to equal intervals τ and find out the distances the square of the initial velocity. Doubling the Table 2.2 Reprint 2025-26 MOTION IN A STRAIGHT LINE 21 initial velocity increases the stopping distance by a factor of 4 (for the same deceleration). For the car of a particular make, the braking distance was found to be 10 m, 20 m, 34 m and 50 m corresponding to velocities of 11, 15, 20 and 25 m/s which are nearly consistent with the above formula. Stopping distance is an important factor considered in setting speed limits, for example, in school zones. ⊳ ⊳ Example 2.7 Reaction time : When a situation demands our immediate action, it takes some time before we really respond. Reaction time is the time a person takes to observe, think Fig. 2.8 Measuring the reaction time. and act. For example, if a person is driving and suddenly a boy appears on the road, then the time elapsed before Answer The ruler drops under free fall. he slams the brakes of the car is the Therefore, vo = 0, and a = – g = –9.8 m s–2. The reaction time. Reaction time depends distance travelled d and the reaction time tr are on complexity of the situation and on related by an individual. You can measure your reaction time by a simple experiment. Take a ruler and ask your friend to drop it vertically through the gap between Or, your thumb and forefinger (Fig. 2.8). Given d = 21.0 cm and g = 9.8 m s–2 the reaction After you catch it, find the distance d time is travelled by the ruler. In a particular case, d was found to be 21.0 cm. ⊳ Estimate reaction time. SUMMARY 1. An object is said to be in motion if its position changes with time. The position of the object can be specified with reference to a conveniently chosen origin. For motion in a straight line, position to the right of the origin is taken as positive and to the left as negative. The average speed of an object is greater or equal to the magnitude of the average velocity over a given time interval. 2. Instantaneous velocity or simply velocity is defined as the limit of the average velocity as the time interval ∆t becomes infinitesimally small : ∆ x d x v = lim v = lim = ∆→t 0 ∆→t 0 ∆t d t The velocity at a particular instant is equal to the slope of the tangent drawn on position-time graph at that instant. Reprint 2025-26 22 PHYSICS 3. Average acceleration is the change in velocity divided by the time interval during which the change occurs : ∆ v a = ∆t 4. Instantaneous acceleration is defined as the limit of the average acceleration as the time interval ∆t goes to zero : ∆v d v a = lim a = lim = ∆→t 0 ∆→t 0 ∆ t d t The acceleration of an object at a particular time is the slope of the velocity-time graph at that instant of time. For uniform motion, acceleration is zero and the x-t graph is a straight line inclined to the time axis and the v-t graph is a straight line parallel to the time axis. For motion with uniform acceleration, x-t graph is a parabola while the v-t graph is a straight line inclined to the time axis. 5. The area under the velocity-time curve between times t1 and t2 is equal to the displacement of the object during that interval of time. 6. For objects in uniformly accelerated rectilinear motion, the five quantities, displacement x, time taken t, initial velocity v0, final velocity v and acceleration a are related by a set of simple equations called kinematic equations of motion : v = v0 + at 1 2 x = v0 t + at 2 v 2 = v 02 + 2ax if the position of the object at time t = 0 is 0. If the particle starts at x = x0 , x in above equations is replaced by (x – x0). Reprint 2025-26 MOTION IN A STRAIGHT LINE 23 POINTS TO PONDER 1. The origin and the positive direction of an axis are a matter of choice. You should first specify this choice before you assign signs to quantities like displacement, velocity and acceleration. 2. If a particle is speeding up, acceleration is in the direction of velocity; if its speed is decreasing, acceleration is in the direction opposite to that of the velocity. This statement is independent of the choice of the origin and the axis. 3. The sign of acceleration does not tell us whether the particle’s speed is increasing or decreasing. The sign of acceleration (as mentioned in point 3) depends on the choice of the positive direction of the axis. For example, if the vertically upward direction is chosen to be the positive direction of the axis, the acceleration due to gravity is negative. If a particle is falling under gravity, this acceleration, though negative, results in increase in speed. For a particle thrown upward, the same negative acceleration (of gravity) results in decrease in speed. 4. The zero velocity of a particle at any instant does not necessarily imply zero acceleration at that instant. A particle may be momentarily at rest and yet have non-zero acceleration. For example, a particle thrown up has zero velocity at its uppermost point but the acceleration at that instant continues to be the acceleration due to gravity. 5. In the kinematic equations of motion [Eq. (2.9)], the various quantities are algebraic, i.e. they may be positive or negative. The equations are applicable in all situations (for one dimensional motion with constant acceleration) provided the values of different quantities are substituted in the equations with proper signs. 6. The definitions of instantaneous velocity and acceleration (Eqs. (2.1) and (2.3)) are exact and are always correct while the kinematic equations (Eq. (2.9)) are true only for motion in which the magnitude and the direction of acceleration are constant during the course of motion. Reprint 2025-26 24 PHYSICS EXERCISES 2.1 In which of the following examples of motion, can the body be considered approximately a point object: (a) a railway carriage moving without jerks between two stations. (b) a monkey sitting on top of a man cycling smoothly on a circular track. (c) a spinning cricket ball that turns sharply on hitting the ground. (d) a tumbling beaker that has slipped off the edge of a table. 2.2 The position-time (x-t) graphs for two children A and B returning from their school O to their homes P and Q respectively are shown in Fig. 2.9. Choose the correct entries in the brackets below ; (a) (A/B) lives closer to the school than (B/A) (b) (A/B) starts from the school earlier than (B/A) (c) (A/B) walks faster than (B/A) (d) A and B reach home at the (same/different) time (e) (A/B) overtakes (B/A) on the road (once/twice). Fig. 2.9 2.3 A woman starts from her home at 9.00 am, walks with a speed of 5 km h–1 on a straight road up to her office 2.5 km away, stays at the office up to 5.00 pm, and returns home by an auto with a speed of 25 km h–1. Choose suitable scales and plot the x-t graph of her motion. 2.4 A drunkard walking in a narrow lane takes 5 steps forward and 3 steps backward, followed again by 5 steps forward and 3 steps backward, and so on. Each step is 1 m long and requires 1 s. Plot the x-t graph of his motion. Determine graphically and otherwise how long the drunkard takes to fall in a pit 13 m away from the start. 2.5 A car moving along a straight highway with speed of 126 km h–1 is brought to a stop within a distance of 200 m. What is the retardation of the car (assumed uniform), and how long does it take for the car to stop ? 2.6 A player throws a ball upwards with an initial speed of 29.4 m s–1. (a) What is the direction of acceleration during the upward motion of the ball ? (b) What are the velocity and acceleration of the ball at the highest point of its motion ? (c) Choose the x = 0 m and t = 0 s to be the location and time of the ball at its highest point, vertically downward direction to be the positive direction of x-axis, and give the signs of position, velocity and acceleration of the ball during its upward, and downward motion. (d) To what height does the ball rise and after how long does the ball return to the player’s hands ? (Take g = 9.8 m s–2 and neglect air resistance). 2.7 Read each statement below carefully and state with reasons and examples, if it is true or false ; A particle in one-dimensional motion (a) with zero speed at an instant may have non-zero acceleration at that instant (b) with zero speed may have non-zero velocity, (c) with constant speed must have zero acceleration, (d) with positive value of acceleration must be speeding up. Reprint 2025-26 MOTION IN A STRAIGHT LINE 25 2.8 A ball is dropped from a height of 90 m on a floor. At each collision with the floor, the ball loses one tenth of its speed. Plot the speed-time graph of its motion between t = 0 to 12 s. 2.9 Explain clearly, with examples, the distinction between : (a) magnitude of displacement (sometimes called distance) over an interval of time, and the total length of path covered by a particle over the same interval; (b) magnitude of average velocity over an interval of time, and the average speed over the same interval. [Average speed of a particle over an interval of time is defined as the total path length divided by the time interval]. Show in both (a) and (b) that the second quantity is either greater than or equal to the first. When is the equality sign true ? [For simplicity, consider one-dimensional motion only]. 2.10 A man walks on a straight road from his home to a market 2.5 km away with a speed of 5 km h–1. Finding the market closed, he instantly turns and walks back home with a speed of 7.5 km h–1. What is the (a) magnitude of average velocity, and (b) average speed of the man over the interval of time (i) 0 to 30 min, (ii) 0 to 50 min, (iii) 0 to 40 min ? [Note: You will appreciate from this exercise why it is better to define average speed as total path length divided by time, and not as magnitude of average velocity. You would not like to tell the tired man on his return home that his average speed was zero !] Fig. 2.10 2.11 In Exercises 2.9 and 2.10, we have carefully distinguished between average speed and magnitude of average velocity. No such distinction is necessary when we consider instantaneous speed and magnitude of velocity. The instantaneous speed is always equal to the magnitude of instantaneous velocity. Why? 2.12 Look at the graphs (a) to (d) (Fig. 2.10) carefully and state, with reasons, which of these cannot possibly represent one-dimensional motion of a particle. 2.13 Figure 2.11shows the x-t plot of one- dimensional motion of a particle. Is it correct to say from the graph that the particle moves Fig. 2.11 in a straight line for t < 0 and on a parabolic path for t >0 ? If not, suggest a suitable physical context for this graph. 2.14 A police van moving on a highway with a speed of 30 km h–1 fires a bullet at a thief’s car speeding away in the same direction with a speed of 192 km h–1. If the muzzle speed of the bullet is 150 m s–1, with what speed does the bullet hit the thief’s car ? (Note: Obtain that speed which is relevant for damaging the thief’s car). Reprint 2025-26 26 PHYSICS 2.15 Suggest a suitable physical situation for each of the following graphs (Fig 2.12): Fig. 2.12 2.16 Figure 2.13 gives the x-t plot of a particle executing one-dimensional simple harmonic motion. (You will learn about this motion in more detail in Chapter13). Give the signs of position, velocity and acceleration variables of the particle at t = 0.3 s, 1.2 s, – 1.2 s. Fig. 2.13 2.17 Figure 2.14 gives the x-t plot of a particle in one-dimensional motion. Three different equal intervals of time are shown. In which interval is the average speed greatest, and in which is it the least ? Give the sign of average velocity for each interval. Fig. 2.14 2.18 Figure 2.15 gives a speed-time graph of a particle in motion along a constant direction. Three equal intervals of time are shown. In which interval is the average acceleration greatest in magnitude? In which interval is the average speed greatest ? Choosing the positive direction as the constant direction of motion, give the signs of v and a in the three intervals. What are the accelerations at the points A, B, C and D ? Fig. 2.15 Reprint 2025-26 CHAPTER THREE MOTION IN A PLANE 3.1 INTRODUCTION In the last chapter we developed the concepts of position, displacement, velocity and acceleration that are needed to 3.1 Introduction describe the motion of an object along a straight line. We 3.2 Scalars and vectors found that the directional aspect of these quantities can be taken care of by + and – signs, as in one dimension only two3.3 Multiplication of vectors by real numbers directions are possible. But in order to describe motion of an 3.4 Addition and subtraction of object in two dimensions (a plane) or three dimensions vectors — graphical method (space), we need to use vectors to describe the above- 3.5 Resolution of vectors mentioned physical quantities. Therefore, it is first necessary to learn the language of vectors. What is a vector? How to3.6 Vector addition — analytical method add, subtract and multiply vectors ? What is the result of 3.7 Motion in a plane multiplying a vector by a real number ? We shall learn this to enable us to use vectors for defining velocity and3.8 Motion in a plane with constant acceleration acceleration in a plane. We then discuss motion of an object 3.9 Projectile motion in a plane. As a simple case of motion in a plane, we shall discuss motion with constant acceleration and treat in detail3.10 Uniform circular motion the projectile motion. Circular motion is a familiar class of Summary motion that has a special significance in daily-life situations. Points to ponder We shall discuss uniform circular motion in some detail. Exercises The equations developed in this chapter for motion in a plane can be easily extended to the case of three dimensions. 3.2 SCALARS AND VECTORS In physics, we can classify quantities as scalars or vectors. Basically, the difference is that a direction is associated with a vector but not with a scalar. A scalar quantity is a quantity with magnitude only. It is specified completely by a single number, along with the proper unit. Examples are : the distance between two points, mass of an object, the temperature of a body and the time at which a certain event happened. The rules for combining scalars are the rules of ordinary algebra. Scalars can be added, subtracted, multiplied and divided Reprint 2025-26 28 PHYSICS just as the ordinary numbers*. For example, represented by another position vector, OP′ if the length and breadth of a rectangle are denoted by r′. The length of the vector r 1.0 m and 0.5 m respectively, then its represents the magnitude of the vector and its perimeter is the sum of the lengths of the direction is the direction in which P lies as seen four sides, 1.0 m + 0.5 m +1.0 m + 0.5 m = from O. If the object moves from P to P′, the 3.0 m. The length of each side is a scalar vector PP′ (with tail at P and tip at P′) is called and the perimeter is also a scalar. Take the displacement vector corresponding to another example: the maximum and motion from point P (at time t) to point P′ (at time t′). minimum temperatures on a particular day are 35.6 °C and 24.2 °C respectively. Then, the difference between the two temperatures is 11.4 °C. Similarly, if a uniform solid cube of aluminium of side 10 cm has a mass of

3.10 In a reaction between A and B, the initial rate of reaction (r0) was measured for different initial concentrations of A and B as given below: A/ mol L–1 0.20 0.20 0.40 B/ mol L–1 0.30 0.10 0.05 r0/mol L–1s–1 5.07 × 10–5 5.07 × 10–5 1.43 × 10–4 What is the order of the reaction with respect to A and B? 3.11 The following results have been obtained during the kinetic studies of the reaction: 2A + B ® C + D Experiment [A]/mol L–1 [B]/mol L–1 Initial rate of formation of D/mol L–1 min–1 I 0.1 0.1 6.0 × 10–3 II 0.3 0.2 7.2 × 10–2 III 0.3 0.4 2.88 × 10–1 IV 0.4 0.1 2.40 × 10–2 Determine the rate law and the rate constant for the reaction. 3.12 The reaction between A and B is first order with respect to A and zero order with respect to B. Fill in the blanks in the following table: Experiment [A]/ mol L–1 [B]/ mol L–1 Initial rate/ mol L–1 min–1 I 0.1 0.1 2.0 × 10–2 II – 0.2 4.0 × 10–2 III 0.4 0.4 – IV – 0.2 2.0 × 10–2 3.13 Calculate the half-life of a first order reaction from their rate constants given below: (i) 200 s–1 (ii) 2 min–1 (iii) 4 years–1 3.14 The half-life for radioactive decay of 14C is 5730 years. An archaeological artifact containing wood had only 80% of the 14C found in a living tree. Estimate the age of the sample. 3.15 The experimental data for decomposition of N2O5 [2N2O5 ® 4NO2 + O2] in gas phase at 318K are given below: t/s 0 400 800 1200 1600 2000 2400 2800 3200 102 × [N2O5]/ 1.63 1.36 1.14 0.93 0.78 0.64 0.53 0.43 0.35 mol L–1 (i) Plot [N2O5] against t. (ii) Find the half-life period for the reaction. (iii) Draw a graph between log[N2O5] and t. (iv) What is the rate law ? Chemistry 86 Reprint 2025-26 (v) Calculate the rate constant. (vi) Calculate the half-life period from k and compare it with (ii).

3.6 VECTOR ADDITION – ANALYTICAL then, a vector T = a + b – c has components : METHOD T x = a x + b x − c x Although the graphical method of adding vectors Ty = a y + b y − c y (3.23b) helps us in visualising the vectors and the T z = a z + b z − c z .resultant vector, it is sometimes tedious and has limited accuracy. It is much easier to add vectors ⊳ Example 3.2 Find the magnitude andby combining their respective components. direction of the resultant of two vectors AConsider two vectors A and B in x-y plane with and B in terms of their magnitudes and components Ax, Ay and Bx, By : angle θ between them. ɵ ɵ A = A x i + A y j (3.18) * Note that angles α, β, and γ are angles in space. They are between pairs of lines, which are not coplanar. Reprint 2025-26 34 PHYSICS ⊳ Example 3.3 A motorboat is racing towards north at 25 km/h and the water current in that region is 10 km/h in the direction of 60° east of south. Find the resultant velocity of the boat. Answer The vector vb representing the velocity of the motorboat and the vector vc representing Fig. 3.10 the water current are shown in Fig. 3.11 in Answer Let OP and OQ represent the two vectors directions specified by the problem. Using the A and B making an angle θ (Fig. 3.10). Then, parallelogram method of addition, the resultant using the parallelogram method of vector R is obtained in the direction shown in the addition, OS represents the resultant vector R : figure. R = A + B SN is normal to OP and PM is normal to OS. From the geometry of the figure, OS2 = ON2 + SN2 but ON = OP + PN = A + B cos θ SN = B sin θ OS2 = (A + B cos θ)2 + (B sin θ)2 or, R2 = A2 + B2 + 2AB cos θ R = A 2 + B 2 + 2AB cosθ (3.24a) In ∆ OSN, SN = OS sinα = R sinα, and in ∆ PSN, SN = PS sin θ = B sin θ Therefore, R sin α = B sin θ R B or, = (3.24b) sin θ sin α Fig. 3.11 Similarly, PM = A sin α = B sin β We can obtain the magnitude of R using the Law A B or, = (3.24c) of cosine : sin β sin α Combining Eqs. (3.24b) and (3.24c), we get R = v 2b + v c2 + 2v bv c cos120 o R A B = = (3.24d) = 25 2 + 10 2 + 2 × 25 × 10 ( -1/2 ) ≅ 22 km/h sin θ sin β sin α To obtain the direction, we apply the Law of sines Using Eq. (3.24d), we get: R vc v c B = sin θ or, sin φ = sin α = sin θ (3.24e) sin θ sin φ R R where R is given by Eq. (3.24a). 10 × sin120 10 3 = = ≅ 0.397 SN B sin θ 21.8 2 × 21.8or, tan α= = (3.24f) OP + PN A + B cos θ φ ≅ 23.4 ⊳ Equation (3.24a) gives the magnitude of the 3.7 MOTION IN A PLANEresultant and Eqs. (3.24e) and (3.24f) its direction. Equation (3.24a) is known as the Law of cosines In this section we shall see how to describe and Eq. (3.24d) as the Law of sines. ⊳ motion in two dimensions using vectors. Reprint 2025-26 MOTION IN A PLANE 35 3.7.1 Position Vector and Displacement Suppose a particle moves along the curve shown The position vector r of a particle P located in a by the thick line and is at P at time t and P′ at plane with reference to the origin of an x-y time t′ [Fig. 3.12(b)]. Then, the displacement is : reference frame (Fig. 3.12) is given by ∆r = r′ – r (3.25) ɵ ɵ and is directed from P to P′. r = x i + y j We can write Eq. (3.25) in a component form: where x and y are components of r along x-, and y- axes or simply they are the coordinates of ɵ ɵ ɵ ɵ ∆r = x' i + y' j − x i + y j ( ) ( )the object. ɵ ɵ = i ∆ x + j ∆ y where ∆x = x ′ – x, ∆y = y′ – y (3.26) Velocity v The average velocity ( ) of an object is the ratio of the displacement and the corresponding time interval : ɵ ɵ ∆ r ∆ x i + ∆y j ɵ ∆ x ɵ ∆ y v = = = i + j (3.27) ∆ t ∆ t ∆ t ∆ t Or, v = v x ˆi + v y j (a) ∆ r Since v = , the direction of the average velocity ∆t is the same as that of ∆r (Fig. 3.12). The velocity (instantaneous velocity) is given by the limiting value of the average velocity as the time interval approaches zero : ∆ r d r v = lim = (3.28) ∆ t → 0 ∆ t d t The meaning of the limiting process can be easily understood with the help of Fig 3.13(a) to (d). In these figures, the thick line represents the path of an object, which is at P at time t. P1, P2 and (b) P3 represent the positions of the object after Fig. 3.12 (a) Position vector r. (b) Displacement ∆r and times ∆t1,∆t2, and ∆t3. ∆r1, ∆r2, and ∆r3 are the average velocity v of a particle. displacements of the object in times ∆t1, ∆t2, and Fig. 3.13 As the time interval ∆t approaches zero, the average velocity approaches the velocity v. The direction of v is parallel to the line tangent to the path. Reprint 2025-26 36 PHYSICS ∆t3, respectively. The direction of the average velocity v is shown in figures (a), (b) and (c) for three decreasing values of ∆t, i.e. ∆t1,∆t2, and ∆t3, (∆t1 > ∆t2 > ∆t3). As ∆t → 0, ∆r → 0 and is along the tangent to the path [Fig. 3.13(d)]. Therefore, the direction of velocity at any point on the path of an object is tangential to the path at that point and is in the direction of motion. We can express v in a component form : Fig. 3.14 The components vx and vy of velocity v and the angle θ it makes with x-axis. Note that dr vx = v cos θ, vy = v sin θ. v = dt The acceleration (instantaneous acceleration)  ∆x ɵ ∆y ɵ  is the limiting value of the average acceleration = lim  i + j  (3.29) ∆t → 0 ∆t ∆t  as the time interval approaches zero : ∆ v ∆x ∆y ɵ ɵ a = lim (3. 32a) + = i lim j lim ∆t → 0 ∆t ∆t → 0 ∆t ∆ t → 0 ∆ t ɵ ɵ ɵ dx ɵ dy ɵ ɵ Since ∆ v = ∆ v x i + ∆ v y j, we have + jOr, v = i = v x i + v y j . dt dt ɵ ∆ v x ɵ ∆ v y dx dy a = i lim + j lim ∆ t → 0 ∆ t ∆ t → 0 ∆ twhere v x = dt , v y = dt (3.30a) ɵ ɵ So, if the expressions for the coordinates x and Or, a = a x i + a y j (3.32b) y are known as functions of time, we can use d v y d v xthese equations to find vx and vy. (3.32c)* where, a x = , a y = The magnitude of v is then d t d t 2 2 As in the case of velocity, we can understand v = v x + v y (3.30b) graphically the limiting process used in defining and the direction of v is given by the angle θ : acceleration on a graph showing the path of the object’s motion. This is shown in Figs. 3.15(a) to  v y  (d). P represents the position of the object at v y −1 tanθ = , θ = tan     (3.30c) time t and P1, P2, P3 positions after time ∆t1, ∆t2,  v x  v x ∆t3, respectively (∆t 1> ∆t2>∆t3). The velocity vectors vx, vy and angle θ are shown in Fig. 3.14 for a at points P, P1, P2, P3 are also shown in Figs. 3.15 velocity vector v at point p. (a), (b) and (c). In each case of ∆t, ∆v is obtained using the triangle law of vector addition. ByAcceleration definition, the direction of average acceleration The average acceleration a of an object for a is the same as that of ∆v. We see that as ∆t time interval ∆t moving in x-y plane is the change decreases, the direction of ∆v changes and in velocity divided by the time interval : consequently, the direction of the acceleration ɵ ɵ changes. Finally, in the limit ∆t g0 [Fig. 3.15(d)], j v x i + v y ∆ v ∆ ( ∆ v y ɵ ) ∆ v x ɵ a = = = i + j (3.31a) the average acceleration becomes the ∆ t ∆ t ∆ t ∆ t instantaneous acceleration and has the direction ɵ ɵ as shown. Or, a = a x i + a y j . (3.31b) * In terms of x and y, ax and ay can be expressed as Reprint 2025-26 MOTION IN A PLANE 37 x (m) Fig. 3.15 The average acceleration for three time intervals (a) ∆t1, (b) ∆t2, and (c) ∆t3, (∆t1> ∆t2> ∆t3). (d) In the limit ∆t g0, the average acceleration becomes the acceleration. Note that in one dimension, the velocity and the acceleration of an object are always along -1  v y  − 1  4  ° θ = tan   = tan   ≅ 53 with x-axis. the same straight line (either in the same  v x   3  direction or in the opposite direction). ⊳ However, for motion in two or three dimensions, velocity and acceleration vectors may have any angle between 0° and 180° 3.8 MOTION IN A PLANE WITH CONSTANT between them. ACCELERATION ⊳ Suppose that an object is moving in x-y plane Example 3.4 The position of a particle is and its acceleration a is constant. Over an given by interval of time, the average acceleration will r = 3.0t ˆi + 2 .0t 2 ˆj + 5 .0 kˆ equal this constant value. Now, let the velocity where t is in seconds and the of the object be v0 at time t = 0 and v at time t. coefficients have the proper units for r to Then, by definition be in metres. (a) Find v(t) and a(t) of the v − v 0 v − v 0 particle. (b) Find the magnitude and a = = t − 0 t direction of v(t) at t = 1.0 s. Or, v = v 0 + a t (3.33a) Answer In terms of components : v x = v ox + a x t dr d ɵ ɵ ɵ v ( t ) = = 3.0 t i + 2.0t2 j + 5.0 k ( ) v y = v oy + a y t (3.33b) d t dt ɵ ɵ = 3.0 i + 4.0t j Let us now find how the position r changes with d v time. We follow the method used in the one- a ( t ) = = +4.0ɵj dt dimensional case. Let ro and r be the position a = 4.0 m s–2 along y- direction vectors of the particle at time 0 and t and let the velocities at these instants be vo and v. Then,At t = 1.0 s, v = 3.0ˆi + 4.0 ˆj over this time interval t, the average velocity is 2 2 -1 (vo + v)/2. The displacement is the average It’s magnitude is v = 3 + 4 = 5.0 m s velocity multiplied by the time interval : and direction is Reprint 2025-26 38 PHYSICS ˆ  v + v 0   ( v 0 + at ) + v 0  = 5.0 t + 1.5 t 2 i + 1.0 t 2 ˆj ( ) t t = r − r0 = 2  2    2 Therefore, x (t ) = 5.0 t + 1.5 t 1 2 y (t ) = +1.0 t 2 at = v 0 t + 2 Given x (t) = 84 m, t = ? 1 2 5.0 t + 1.5 t 2 = 84 ⇒ t = 6 s Or, r = r0 + v 0t + at (3.34a) At t = 6 s, y = 1.0 (6)2 = 36.0 m 2 d r 2.0 t ˆjIt can be easily verified that the derivative of Now, the velocity v = = ( 5.0 + 3.0 t ) ˆi + d t d r ɵ ɵEq. (3.34a), i.e. gives Eq.(3.33a) and it also At t = 6 s, v = 23.0 i + 12.0 j d t satisfies the condition that at t=0, r = ro. speed = v = 232 + 122 ≅ 26 m s−1 . ⊳Equation (3.34a) can be written in component form as 3.9 PROJECTILE MOTION 1 2 x = x 0 + v ox t + a x t As an application of the ideas developed in the 2 previous sections, we consider the motion of a 1 2 projectile. An object that is in flight after being y = y 0 + v oy t + a y t (3.34b) thrown or projected is called a projectile. Such 2 a projectile might be a football, a cricket ball, a One immediate interpretation of Eq.(3.34b) is that baseball or any other object. The motion of a the motions in x- and y-directions can be treated projectile may be thought of as the result of two independently of each other. That is, motion in separate, simultaneously occurring components a plane (two-dimensions) can be treated as two of motions. One component is along a horizontal separate simultaneous one-dimensional direction without any acceleration and the other motions with constant acceleration along two along the vertical direction with constant perpendicular directions. This is an important acceleration due to the force of gravity. It was result and is useful in analysing motion of objects Galileo who first stated this independency of the in two dimensions. A similar result holds for three horizontal and the vertical components ofdimensions. The choice of perpendicular projectile motion in his Dialogue on the greatdirections is convenient in many physical world systems (1632).situations, as we shall see in section 3.9 for In our discussion, we shall assume that theprojectile motion. air resistance has negligible effect on the motion ⊳ Example 3.5 A particle starts from origin of the projectile. Suppose that the projectile is launched with velocity vo that makes an angle at t = 0 with a velocity 5.0 î m/s and moves in x-y plane under action of a force which θo with the x-axis as shown in Fig. 3.16. produces a constant acceleration of (3.0iɵ+2.0jɵ) m/s 2. (a) What is the After the object has been projected, the acceleration acting on it is that due to gravity y-coordinate of the particle at the instant which is directed vertically downward: its x-coordinate is 84 m ? (b) What is the ɵ speed of the particle at this time ? a = −g j Or, ax = 0, ay = – g (3.35) Answer From Eq. (3.34a) for r0 = 0, the position The components of initial velocity vo are : of the particle is given by 1 at 2 vox = vo cos θo r (t ) = v 0 t + 2 2 voy= vo sin θo (3.36) t 3.0ˆi + 2.0 ˆj = 5.0 ˆi t + (1/2 )( ) Reprint 2025-26 MOTION IN A PLANE 39 Now, since g, θo and vo are constants, Eq. (3.39) is of the form y = a x + b x2, in which a and b are constants. This is the equation of a parabola, i.e. the path of the projectile is a parabola (Fig. 3.17). Fig 3.16 Motion of an object projected with velocity vo at angle θ0. If we take the initial position to be the origin of the reference frame as shown in Fig. 3.16, we have : xo = 0, yo = 0 Then, Eq.(3.34b) becomes : x = vox t = (vo cos θo ) t and y = (vo sin θo ) t – ( ½ )g t2 (3.37) Fig. 3.17 The path of a projectile is a parabola. The components of velocity at time t can be Time of maximum height obtained using Eq.(3.33b) : How much time does the projectile take to reach the vx = vox = vo cos θo maximum height ? Let this time be denoted by tm. Since at this point, vy= 0, we have from Eq. (3.38): vy = vo sin θo – g t (3.38) vy = vo sinθo – g tm = 0 Equation (3.37) gives the x-, and y-coordinates Or, tm = vo sinθo /g (3.40a) of the position of a projectile at time t in terms of The total time Tf during which the projectile is two parameters — initial speed vo and projection in flight can be obtained by putting y = 0 in angle θo. Notice that the choice of mutually Eq. (3.37). We get : perpendicular x-, and y-directions for the analysis of the projectile motion has resulted in Tf = 2 (vo sin θo )/g (3.40b) a simplification. One of the components of Tf is known as the time of flight of the projectile. velocity, i.e. x-component remains constant We note that Tf = 2 tm , which is expected throughout the motion and only the because of the symmetry of the parabolic path. y- component changes, like an object in free fall Maximum height of a projectile in vertical direction. This is shown graphically The maximum height hm reached by theat few instants in Fig. 3.17. Note that at the point projectile can be calculated by substituting of maximum height, vy= 0 and therefore, t = tm in Eq. (3.37) : -1 v y 2 = oθ = tan    g  v 0 sinθ0 v 0 sinθ0 v x y = h m = ( v 0 sinθ0 )  −   Equation of path of a projectile  g  2  g  What is the shape of the path followed by the ( v 0 sinθ0 ) 2 projectile? This can be seen by eliminating the Or, h m = (3.41) 2gtime between the expressions for x and y as given in Eq. (3.37). We obtain: Horizontal range of a projectile g 2 The horizontal distance travelled by a projectile from x y = ( tan θo ) x − (3.39) its initial position (x = y = 0) to the position where it 2 (v o cosθo )2 passes y = 0 during its fall is called the horizontal Reprint 2025-26 40 PHYSICS range, R. It is the distance travelled during the time y (t) = yo + voy t +(1/2) ay t2 of flight Tf . Therefore, the range R is Here, xo = yo = 0, voy = 0, ay = –g = –9.8 m s-2, R = (vo cos θo) (Tf ) vox = 15 m s-1. The stone hits the ground when y(t) = – 490 m. =(vo cos θo) (2 vo sin θo)/g – 490 m = –(1/2)(9.8) t2. 2 sin 2θ0 This gives t =10 s. v 0 Or, R = (3.42a) The velocity components are vx = vox and g vy = voy – g t Equation (3.42a) shows that for a given so that when the stone hits the ground : projection velocity vo , R is maximum when sin vox = 15 m s–1 2θ0 is maximum, i.e., when θ0 = 450. voy = 0 – 9.8 × 10 = – 98 m s–1 The maximum horizontal range is, therefore, Therefore, the speed of the stone is 2 v 0 v 2x + v y2 = 15 2 + 98 2 = 99 m s −1 ⊳ R m = (3.42b) g ⊳ ⊳ Example 3.6 Galileo, in his book Two new Example 3.8 A cricket ball is thrown at a sciences, stated that “for elevations which speed of 28 m s–1 in a direction 30° above exceed or fall short of 45° by equal amounts, the horizontal. Calculate (a) the maximum the ranges are equal”. Prove this statement. height, (b) the time taken by the ball to return to the same level, and (c) the distance from the thrower to the point Answer For a projectile launched with velocity where the ball returns to the same level. vo at an angle θo , the range is given by v 02 sin2θ0 R = Answer (a) The maximum height is given by g 2 2 sin sin 30 ( 28 ( v 0 θo ) ° ) m = m =Now, for angles, (45° + α) and ( 45° – α), 2θo is h 2 2 g ( 9.8 )(90° + 2α) and ( 90° – 2α) , respectively. The values of sin (90° + 2α) and sin (90° – 2α) are 14 × 14 = = 10.0 mthe same, equal to that of cos 2α. Therefore, 2 × 9.8 ranges are equal for elevations which exceed or fall short of 45° by equal amounts α. ⊳ (b) The time taken to return to the same level is Tf = (2 vo sin θo )/g = (2× 28 × sin 30° )/9.8 ⊳ = 28/9.8 s = 2.9 s Example 3.7 A hiker stands on the edge (c) The distance from the thrower to the point of a cliff 490 m above the ground and where the ball returns to the same level is throws a stone horizontally with an initial speed 2 of 15 m s-1. Neglecting air resistance, v o sin2θo 28 × 28 × sin60o ( ) = = 69 m ⊳ find the time taken by the stone to reach R = g 9.8 the ground, and the speed with which it hits the ground. (Take g = 9.8 m s-2 ). 3.10 UNIFORM CIRCULAR MOTION Answer We choose the origin of the x-,and y- When an object follows a circular path at a axis at the edge of the cliff and t = 0 s at the constant speed, the motion of the object is called instant the stone is thrown. Choose the positive uniform circular motion. The word “uniform” direction of x-axis to be along the initial velocity refers to the speed, which is uniform (constant) and the positive direction of y-axis to be the throughout the motion. Suppose an object is vertically upward direction. The x-, and y- moving with uniform speed v in a circle of radius components of the motion can be treated R as shown in Fig. 3.18. Since the velocity of the independently. The equations of motion are : object is changing continuously in direction, the x (t) = xo + vox t object undergoes acceleration. Let us find the magnitude and the direction of this acceleration. Reprint 2025-26 MOTION IN A PLANE 41 Fig. 3.18 Velocity and acceleration of an object in uniform circular motion. The time interval ∆t decreases from (a) to (c) where it is zero. The acceleration is directed, at each point of the path, towards the centre of the circle. Let r and r′ be the position vectors and v and r′ be ∆θ. Since the velocity vectors v and v′ are v′ the velocities of the object when it is at point P always perpendicular to the position vectors, the and P′ as shown in Fig. 3.18(a). By definition, angle between them is also ∆θ . Therefore, the velocity at a point is along the tangent at that triangle CPP′ formed by the position vectors and point in the direction of motion. The velocity the triangle GHI formed by the velocity vectors vectors v and v′ are as shown in Fig. 3.18(a1). v, v′ and ∆v are similar (Fig. 3.18a). Therefore, ∆v is obtained in Fig. 3.18 (a2) using the triangle the ratio of the base-length to side-length for law of vector addition. Since the path is circular, one of the triangles is equal to that of the other v is perpendicular to r and so is v′ to r′. triangle. That is : Therefore, ∆v is perpendicular to ∆r. Since  ∆v  ∆ v ∆ r average acceleration is along ∆v  a =  , the =  ∆t  v R average acceleration a is perpendicular to ∆r. If we place ∆v on the line that bisects the angle ∆ r Or, ∆ v = v between r and r′, we see that it is directed towards R the centre of the circle. Figure 3.18(b) shows the Therefore, same quantities for smaller time interval. ∆v and ∆ v v ∆ r v ∆r hence a is again directed towards the centre. a = lim = lim = lim t ∆ t → 0 R ∆ t R ∆ t → 0 ∆ tIn Fig. 3.18(c), ∆tŽ 0 and the average ∆ t → 0 ∆ acceleration becomes the instantaneous If ∆t is small, ∆θ will also be small and then arc acceleration. It is directed towards the centre*. PP′ can be approximately taken to be|∆r|: Thus, we find that the acceleration of an object ∆ r ≅v∆ t in uniform circular motion is always directed ∆r towards the centre of the circle. Let us now find ≅ v the magnitude of the acceleration. ∆ t The magnitude of a is, by definition, given by ∆ r lim = v ∆v Or, ∆ t → 0 ∆ t a = lim ∆ t → 0 ∆t Let the angle between position vectors r and Therefore, the centripetal acceleration ac is : * In the limit ∆tŽ0, ∆r becomes perpendicular to r. In this limit ∆v→ 0 and is consequently also perpendicular to V. Therefore, the acceleration is directed towards the centre, at each point of the circular path. Reprint 2025-26 42 PHYSICS 2 2 2  v  v R ω 2  R ac = = = ω a c =  R v = v2/R (3.43) R R Thus, the acceleration of an object moving with 2 a c = ω R (3.46) speed v in a circle of radius R has a magnitude v 2/R and is always directed towards the centre. The time taken by an object to make one revolution This is why this acceleration is called centripetal is known as its time period T and the number ofacceleration (a term proposed by Newton). A revolution made in one second is called itsthorough analysis of centripetal acceleration was frequency ν (=1/T). However, during this timefirst published in 1673 by the Dutch scientist the distance moved by the object is s = 2πR.Christiaan Huygens (1629-1695) but it was probably known to Newton also some years earlier. Therefore, v = 2πR/T =2πRν (3.47) “Centripetal” comes from a Greek term which means In terms of frequency ν, we have ‘centre-seeking’. Since v and R are constant, the ω = 2πν magnitude of the centripetal acceleration is also v = 2πRν constant. However, the direction changes — ac = 4π2 ν2R (3.48)pointing always towards the centre. Therefore, a ⊳centripetal acceleration is not a constant vector. Example 3.9 An insect trapped in a We have another way of describing the circular groove of radius 12 cm moves along velocity and the acceleration of an object in the groove steadily and completes 7 uniform circular motion. As the object moves revolutions in 100 s. (a) What is the from P to P′ in time ∆t (= t′ – t), the line CP angular speed, and the linear speed of the (Fig. 3.18) turns through an angle ∆θ as shown motion? (b) Is the acceleration vector a in the figure. ∆θ is called angular distance. We constant vector ? What is its magnitude ? define the angular speed ω (Greek letter omega) as the time rate of change of angular Answer This is an example of uniform circular displacement : motion. Here R = 12 cm. The angular speed ω is ∆θ given by ω = ∆t (3.44) ω = 2π/T = 2π × 7/100 = 0.44 rad/s The linear speed v is :Now, if the distance travelled by the object during the time ∆t is ∆s, i.e. PP′ is ∆s, then : v =ω R = 0.44 s-1 × 12 cm = 5.3 cm s-1 ∆ s The direction of velocity v is along the tangent v = ∆t to the circle at every point. The acceleration is directed towards the centre of the circle. Sincebut ∆s = R ∆θ. Therefore : this direction changes continuously, ∆θ v = R = R ω acceleration here is not a constant vector. ∆ t However, the magnitude of acceleration is v = R ω (3.45) constant: a = ω2 R = (0.44 s–1)2 (12 cm)We can express centripetal acceleration ac in terms of angular speed : = 2.3 cm s-2 ⊳ Reprint 2025-26 MOTION IN A PLANE 43 SUMMARY 1. Scalar quantities are quantities with magnitudes only. Examples are distance, speed, mass and temperature. 2. Vector quantities are quantities with magnitude and direction both. Examples are displacement, velocity and acceleration. They obey special rules of vector algebra. 3. A vector A multiplied by a real number λ is also a vector, whose magnitude is λ times the magnitude of the vector A and whose direction is the same or opposite depending upon whether λ is positive or negative. 4. Two vectors A and B may be added graphically using head-to-tail method or parallelogram method. 5. Vector addition is commutative : A + B = B + A It also obeys the associative law : (A + B) + C = A + (B + C) 6. A null or zero vector is a vector with zero magnitude. Since the magnitude is zero, we don’t have to specify its direction. It has the properties : A + 0 = A λ0 = 0 0 A = 0 7. The subtraction of vector B from A is defined as the sum of A and –B : A – B = A+ (–B) 8. A vector A can be resolved into component along two given vectors a and b lying in the same plane : A = λ a + µ b where λ and µ are real numbers. 9. A unit vector associated with a vector A has magnitude 1 and is along the vector A: A ˆn = A ɵ ɵ ɵ The unit vectors i, j, k are vectors of unit magnitude and point in the direction of the x-, y-, and z-axes, respectively in a right-handed coordinate system. 10. A vector A can be expressed as ɵ ɵ A = A x i + Ay j where Ax, Ay are its components along x-, and y -axes. If vector A makes an angle θ A y 2 2 with the x-axis, then Ax = A cos θ, Ay=A sin θ and A = A = A x + A y , tanθ = . A x 11. Vectors can be conveniently added using analytical method. If sum of two vectors A and B, that lie in x-y plane, is R, then : ɵ R = R x i + Ry ɵ,j where, Rx = Ax + Bx, and Ry = Ay + By ɵ ɵ 12. The position vector of an object in x-y plane is given by r = x i + y j and the displacement from position r to position r’ is given by ∆r = r′− r ɵ ɵ = ( x ′ − x ) i + (y ′ − y ) j ɵ ɵ = ∆x i + ∆y j 13. If an object undergoes a displacement ∆r in time ∆t, its average velocity is given by ∆ r v = . The velocity of an object at time t is the limiting value of the average velocity ∆t as ∆t tends to zero : Reprint 2025-26 44 PHYSICS ∆ r d r v = lim = . It can be written in unit vector notation as : ∆ t →0 ∆ t dt ɵ ɵ ɵ dx dy dz = y v = v x i + v y j + v z k where v x = dt , v dt , v z = dt When position of an object is plotted on a coordinate system, v is always tangent to the curve representing the path of the object. 14. If the velocity of an object changes from v to v′in time ∆t, then its average acceleration v − v' ∆ v is given by: a = = ∆ t ∆t The acceleration a at any time t is the limiting value of a as ∆t Ž0 : ∆ v dv a = lim = ∆ t → 0 ∆ t dt ɵ ɵ ɵ In component form, we have : a = a x i + a y j + a z k dvy dv x dv z where, a x = , a y = , a z = dt dt dt 15. If an object is moving in a plane with constant acceleration a = a = a x2 + a y2 and its position vector at time t = 0 is ro, then at any other time t, it will be at a point given by: 1 2 r = ro + v o t + at 2 and its velocity is given by : v = vo + a t where vo is the velocity at time t = 0 In component form : 1 2 x = x o + v ox t + a x t 2 1 2 y = yo + v oy t + a y t 2 v x = v ox + a x t v y = v oy + a y t Motion in a plane can be treated as superposition of two separate simultaneous one- dimensional motions along two perpendicular directions 16. An object that is in flight after being projected is called a projectile. If an object is projected with initial velocity vo making an angle θo with x-axis and if we assume its initial position to coincide with the origin of the coordinate system, then the position and velocity of the projectile at time t are given by : x = (vo cos θo) t y = (vo sin θo) t − (1/2) g t2 vx = vox = vo cos θo vy = vo sin θo − g t The path of a projectile is parabolic and is given by : 2 gx y = ( tanθ0 ) x – 2 2 (v o cosθo ) The maximum height that a projectile attains is : Reprint 2025-26 MOTION IN A PLANE 45 (v o sinq o )2 h m = 2g The time taken to reach this height is : v o sinθo t m = g The horizontal distance travelled by a projectile from its initial position to the position it passes y = 0 during its fall is called the range, R of the projectile. It is : v o2 R = sin2θo g 17. When an object follows a circular path at constant speed, the motion of the object is called uniform circular motion. The magnitude of its acceleration is ac = v2 /R. The direction of ac is always towards the centre of the circle. The angular speed ω, is the rate of change of angular distance. It is related to velocity v by v = ω R. The acceleration is ac = ω 2R. If T is the time period of revolution of the object in circular motion and ν is its frequency, we have ω = 2π ν, v = 2πνR, ac = 4π2ν2R Reprint 2025-26 46 PHYSICS POINTS TO PONDER 1. The path length traversed by an object between two points is, in general, not the same as the magnitude of displacement. The displacement depends only on the end points; the path length (as the name implies) depends on the actual path. The two quantities are equal only if the object does not change its direction during the course of motion. In all other cases, the path length is greater than the magnitude of displacement. 2. In view of point 1 above, the average speed of an object is greater than or equal to the magnitude of the average velocity over a given time interval. The two are equal only if the path length is equal to the magnitude of displacement. 3. The vector equations (3.33a) and (3.34a) do not involve any choice of axes. Of course, you can always resolve them along any two independent axes. 4. The kinematic equations for uniform acceleration do not apply to the case of uniform circular motion since in this case the magnitude of acceleration is constant but its direction is changing. 5. An object subjected to two velocities v1 and v2 has a resultant velocity v = v1 + v2. Take care to distinguish it from velocity of object 1 relative to velocity of object 2 : v12= v1 − v2. Here v1 and v2 are velocities with reference to some common reference frame. 6. The resultant acceleration of an object in circular motion is towards the centre only if the speed is constant. 7. The shape of the trajectory of the motion of an object is not determined by the acceleration alone but also depends on the initial conditions of motion ( initial position and initial velocity). For example, the trajectory of an object moving under the same acceleration due to gravity can be a straight line or a parabola depending on the initial conditions. EXERCISES 3.1 State, for each of the following physical quantities, if it is a scalar or a vector : volume, mass, speed, acceleration, density, number of moles, velocity, angular frequency, displacement, angular velocity. 3.2 Pick out the two scalar quantities in the following list : force, angular momentum, work, current, linear momentum, electric field, average velocity, magnetic moment, relative velocity. 3.3 Pick out the only vector quantity in the following list : Temperature, pressure, impulse, time, power, total path length, energy, gravitational potential, coefficient of friction, charge. 3.4 State with reasons, whether the following algebraic operations with scalar and vector physical quantities are meaningful : (a) adding any two scalars, (b) adding a scalar to a vector of the same dimensions , (c) multiplying any vector by any scalar, (d) multiplying any two scalars, (e) adding any two vectors, (f) adding a component of a vector to the same vector. 3.5 Read each statement below carefully and state with reasons, if it is true or false : (a) The magnitude of a vector is always a scalar, (b) each component of a vector is always a scalar, (c) the total path length is always equal to the magnitude of the displacement vector of a particle. (d) the average speed of a particle (defined as total path length divided by the time taken to cover the path) is either greater or equal to the magnitude of average velocity of the particle over the same interval of time, (e) Three vectors not lying in a plane can never add up to give a null vector. 3.6 Establish the following vector inequalities geometrically or otherwise : (a) |a+b| < |a| + |b| (b) |a+b| > ||a| −|b|| Reprint 2025-26 MOTION IN A PLANE 47 (c) |a−b| < |a| + |b| (d) |a−b| > ||a| − |b|| When does the equality sign above apply? 3.7 Given a + b + c + d = 0, which of the following statements are correct : Q (a) a, b, c, and d must each be a null vector, (b) The magnitude of (a + c) equals the magnitude of ( b + d), (c) The magnitude of a can never be greater than the sum of the magnitudes of b, c, and d, (d) b + c must lie in the plane of a and d if a and d are not collinear, and in the line of a and d, if they are collinear ? 3.8 Three girls skating on a circular ice ground of radius 200 m start from a point P on the edge of the ground and reach a point Q diametrically opposite to P following different paths as shown in Fig. 3.19. What is the magnitude of the displacement vector for each ? For Fig. 3.19 which girl is this equal to the actual length of path skate ? 3.9 A cyclist starts from the centre O of a circular park of radius 1 km, reaches the edge P of the park, then cycles along the circumference, and returns to the centre along QO as shown in Fig. 3.20. If the round trip takes 10 min, what is the (a) net displacement, (b) average velocity, and (c) average speed of the cyclist ? Fig. 3.20 3.10 On an open ground, a motorist follows a track that turns to his left by an angle of 600 after every 500 m. Starting from a given turn, specify the displacement of the motorist at the third, sixth and eighth turn. Compare the magnitude of the displacement with the total path length covered by the motorist in each case. 3.11 A passenger arriving in a new town wishes to go from the station to a hotel located 10 km away on a straight road from the station. A dishonest cabman takes him along a circuitous path 23 km long and reaches the hotel in 28 min. What is (a) the average speed of the taxi, (b) the magnitude of average velocity ? Are the two equal ? 3.12 The ceiling of a long hall is 25 m high. What is the maximum horizontal distance that a ball thrown with a speed of 40 m s-1 can go without hitting the ceiling of the hall ? 3.13 A cricketer can throw a ball to a maximum horizontal distance of 100 m. How much high above the ground can the cricketer throw the same ball ? Reprint 2025-26 48 PHYSICS 3.14 A stone tied to the end of a string 80 cm long is whirled in a horizontal circle with a constant speed. If the stone makes 14 revolutions in 25 s, what is the magnitude and direction of acceleration of the stone ? 3.15 An aircraft executes a horizontal loop of radius 1.00 km with a steady speed of 900 km/h. Compare its centripetal acceleration with the acceleration due to gravity. 3.16 Read each statement below carefully and state, with reasons, if it is true or false : (a) The net acceleration of a particle in circular motion is always along the radius of the circle towards the centre (b) The velocity vector of a particle at a point is always along the tangent to the path of the particle at that point (c) The acceleration vector of a particle in uniform circular motion averaged over one cycle is a null vector 3.17 The position of a particle is given by r = 3.0t ˆi − 2.0t 2 ˆj + 4.0 kˆ m where t is in seconds and the coefficients have the proper units for r to be in metres. (a) Find the v and a of the particle? (b) What is the magnitude and direction of velocity of the particle at t = 2.0 s ? 3.18 A particle starts from the origin at t = 0 s with a velocity of 10.0 jɵ m/s and moves in ɵ ɵ the x-y plane with a constant acceleration of 8.0 i + 2.0 j m s-2. (a) At what time is ( ) the x- coordinate of the particle 16 m? What is the y-coordinate of the particle at that time? (b) What is the speed of the particle at the time ? 3.19 ɵi and ɵj are unit vectors along x- and y- axis respectively. What is the magnitude ɵ ɵ ɵ ɵ and direction of the vectors i + j , and i − j ? What are the components of a vector ɵ ɵ ɵ ɵ ɵ ɵ A= 2 i + 3 j along the directions of i + j and i −?j [You may use graphical method] 3.20 For any arbitrary motion in space, which of the following relations are true : (a) vaverage = (1/2) (v (t1) + v (t2)) (b) v average = [r(t2) - r(t1) ] /(t2 – t1) (c) v (t) = v (0) + a t (d) r (t) = r (0) + v (0) t + (1/2) a t2 (e) a average =[ v (t2) - v (t1 )] /( t2 – t1) (The ‘average’ stands for average of the quantity over the time interval t1 to t2) 3.21 Read each statement below carefully and state, with reasons and examples, if it is true or false : A scalar quantity is one that (a) is conserved in a process (b) can never take negative values (c) must be dimensionless (d) does not vary from one point to another in space (e) has the same value for observers with different orientations of axes. 3.22 An aircraft is flying at a height of 3400 m above the ground. If the angle subtended at a ground observation point by the aircraft positions 10.0 s a part is 30°, wat is the speed of the aircraft ? Reprint 2025-26 CHAPTER FOUR LAWS OF MOTION 4.1 INTRODUCTION In the preceding Chapter, our concern was to describe the motion of a particle in space quantitatively. We saw that 4.1 Introduction uniform motion needs the concept of velocity alone whereas 4.2 Aristotle’s fallacy non-uniform motion requires the concept of acceleration in 4.3 The law of inertia addition. So far, we have not asked the question as to what governs the motion of bodies. In this chapter, we turn to this4.4 Newton’s first law of motion basic question.4.5 Newton’s second law of Let us first guess the answer based on our common motion experience. To move a football at rest, someone must kick it.4.6 Newton’s third law of motion To throw a stone upwards, one has to give it an upward