6.2 Use Lenz’s law to determine the direction of induced current in the situations described by Fig. 6.16: (a) A wire of irregular shape turning into a circular shape; 175 Reprint 2025-26 Physics (b) A circular loop being deformed into a narrow straight wire. FIGURE 6.16 6.3 A long solenoid with 15 turns per cm has a small loop of area 2.0 cm2 placed inside the solenoid normal to its axis. If the current carried by the solenoid changes steadily from 2.0 A to 4.0 A in 0.1 s, what is the induced emf in the loop while the current is changing? 6.4 A rectangular wire loop of sides 8 cm and 2 cm with a small cut is moving out of a region of uniform magnetic field of magnitude 0.3 T directed normal to the loop. What is the emf developed across the cut if the velocity of the loop is 1 cm s–1 in a direction normal to the (a) longer side, (b) shorter side of the loop? For how long does the induced voltage last in each case? 6.5 A 1.0 m long metallic rod is rotated with an angular frequency of 400 rad s–1 about an axis normal to the rod passing through its one end. The other end of the rod is in contact with a circular metallic ring. A constant and uniform magnetic field of 0.5 T parallel to the axis exists everywhere. Calculate the emf developed between the centre and the ring. 6.6 A horizontal straight wire 10 m long extending from east to west is falling with a speed of 5.0 m s–1, at right angles to the horizontal component of the earth’s magnetic field, 0.30 ´ 10–4 Wb m–2. (a) What is the instantaneous value of the emf induced in the wire? (b) What is the direction of the emf? (c) Which end of the wire is at the higher electrical potential? 6.7 Current in a circuit falls from 5.0 A to 0.0 A in 0.1 s. If an average emf of 200 V induced, give an estimate of the self-inductance of the circuit. 6.8 A pair of adjacent coils has a mutual inductance of 1.5 H. If the current in one coil changes from 0 to 20 A in 0.5 s, what is the change of flux linkage with the other coil? Reprint 2025-26 Chapter Seven ALTERNATING CURRENT 7.1 INTRODUCTION We have so far considered direct current (dc) sources and circuits with dc sources. These currents do not change direction with time. But voltages and currents that vary with time are very common. The electric mains supply in our homes and offices is a voltage that varies like a sine function with time. Such a voltage is called alternating voltage (ac voltage) and the current driven by it in a circuit is called the alternating current (ac current)*. Today, most of the electrical devices we use require ac voltage. This is mainly because most of the electrical energy sold by power companies is transmitted and distributed as alternating current. The main reason for preferring use of ac voltage over dc voltage is that ac voltages can be easily and efficiently converted from one voltage to the other by means of transformers. Further, electrical energy can also be transmitted economically over long distances. AC circuits exhibit characteristics which are exploited in many devices of daily use. For example, whenever we tune our radio to a favourite station, we are taking advantage of a special property of ac circuits – one of many that you will study in this chapter. * The phrases ac voltage and ac current are contradictory and redundant, respectively, since they mean, literally, alternating current voltage and alternating current current. Still, the abbreviation ac to designate an electrical quantity displaying simple harmonic time dependance has become so universally accepted that we follow others in its use. Further, voltage – another phrase commonly used means potential difference between two points. Reprint 2025-26 Physics 7.2 AC VOLTAGE APPLIED TO A RESISTOR Figure 7.1 shows a resistor connected to a source ε of ac voltage. The symbol for an ac source in a circuit diagram is . We consider a source which produces sinusoidally varying potential difference across its terminals. Let this potential difference, also called ac voltage, be given by v = vm sin ωt (7.1) where vm is the amplitude of the oscillating potential difference and ω is its angular frequency. Nicola Tesla (1856 – 1943) Serbian-American scientist, inventor and genius. He conceived the idea of the rotating1943) magnetic field, which is the – basis of practically all alternating current machinery, and which(1856 helped usher in the age of FIGURE 7.1 AC voltage applied to a resistor. electric power. He also invented among other To find the value of current through the resistor, we things the induction motor, ε()t = 0 (refer to Section the polyphase system of ac apply Kirchhoff’s loop rule ∑TESLA power, and the high 3.12), to the circuit shown in Fig. 7.1 to get frequency induction coil v m sin ωt = i R (the Tesla coil) used in radio and television sets and v m i = sin ωtNICOLA other electronic equipment. or R The SI unit of magnetic field is named in his honour. Since R is a constant, we can write this equation as i = i m sin ωt (7.2) where the current amplitude im is given by v m i m = (7.3) R Equation (7.3) is Ohm’s law, which for resistors, works equally well for both ac and dc voltages. The voltage across a pure resistor and the current through it, given by Eqs. (7.1) and (7.2) are plotted as a function of time in Fig. 7.2. Note, in particular that both v and i reach zero, minimum and maximum values at the same time. Clearly, the voltage and current are in phase with FIGURE 7.2 In a pure resistor, the voltage and each other. current are in phase. The We see that, like the applied voltage, the current varies minima, zero and maxima sinusoidally and has corresponding positive and negative values occur at the same during each cycle. Thus, the sum of the instantaneous current respective times. values over one complete cycle is zero, and the average current 178 is zero. The fact that the average current is zero, however, does Reprint 2025-26 Alternating Current not mean that the average power consumed is zero and that there is no dissipation of electrical energy. As you know, Joule heating is given by i2R and depends on i2 (which is always positive whether i is positive or negative) and not on i. Thus, there is Joule heating and dissipation of electrical energy when an ac current passes through a resistor. The instantaneous power dissipated in the resistor is p = i 2 R = i m2 R sin 2 ωt (7.4) The average value of p over a cycle is* p = < i 2 R > = < i m2 R sin 2 ωt > [7.5(a)] where the bar over a letter (here, p) denotes its average George Westinghouse value and <......> denotes taking average of the quantity (1846 – 1914) A leading inside the bracket. Since, i2m and R are constants, proponent of the use of p = i m2 R < sin 2 ωt > [7.5(b)] alternating current overUsing the trigonometric identity, sin2 wt = direct current. Thus, GEORGE he came into conflict 1/2 (1– cos 2wt), we have < sin2 wt > = (1/2) (1– < cos 2wt >) with Thomas Alva Edison, and since < cos2wt > = 0**, we have, an advocate of direct 2 1 current. Westinghouse < sin ωt > = was convinced that the 2 technology of alternating Thus, current was the key to 1 2 the electrical future. p = i m R [7.5(c)] He founded the famous 2 Company named after him WESTINGHOUSE To express ac power in the same form as dc power and enlisted the services (P = I2R), a special value of current is defined and used. of Nicola Tesla and It is called, root mean square (rms) or effective current other inventors in the (1846(Fig. 7.3) and is denoted by Irms or I. development of alternating current motors and – apparatus for the transmission of high tension current, pioneering 1914) in large scale lighting. FIGURE 7.3 The rms current I is related to the peak current im by I = mi / 2 = 0.707 im. 1 T F (t ) d t* The average value of a function F (t) over a period T is given by F (t ) = T ∫0 1 T 1  sin 2ωt  T 1 < cos 2ωt > = ∫ cos 2ω t dt = = [ sin 2ω T − 0 ] = 0** T 0 T  2ω  0 2ωT 179 Reprint 2025-26 Physics It is defined by 2 1 2 i m I = i = i m = 2 2 = 0.707 im (7.6) In terms of I, the average power, denoted by P is 1 2 2 P = p = i m R = I R (7.7) 2 Similarly, we define the rms voltage or effective voltage by v m V = = 0.707 vm (7.8) 2 From Eq. (7.3), we have vm = imR v m i m or, = R 2 2 or, V = IR (7.9) Equation (7.9) gives the relation between ac current and ac voltage and is similar to that in the dc case. This shows the advantage of introducing the concept of rms values. In terms of rms values, the equation for power [Eq. (7.7)] and relation between current and voltage in ac circuits are essentially the same as those for the dc case. It is customary to measure and specify rms values for ac quantities. For example, the household line voltage of 220 V is an rms value with a peak voltage of vm = 2 V = (1.414)(220 V) = 311 V In fact, the I or rms current is the equivalent dc current that would produce the same average power loss as the alternating current. Equation (7.7) can also be written as P = V2 / R = I V (since V = I R) Example 7.1 A light bulb is rated at 100W for a 220 V supply. Find (a) the resistance of the bulb; (b) the peak voltage of the source; and (c) the rms current through the bulb. Solution (a) We are given P = 100 W and V = 220 V. The resistance of the bulb is 2 V 2 ( 220 V ) R = = = 484 Ω P 100 W (b) The peak voltage of the source is V 7.1 v m = 2V = 311 (c) Since, P = I V P 100 W I 0.454A EXAMPLE V 220 V Reprint 2025-26 Alternating Current

3.3 At room temperature (27.0 °C) the resistance of a heating element is 100 Ω. What is the temperature of the element if the resistance is found to be 117 Ω, given that the temperature coefficient of the material of the resistor is 1.70 × 10–4 °C–1. 105 Reprint 2025-26 Physics 3.4 A negligibly small current is passed through a wire of length 15 m and uniform cross-section 6.0 × 10–7 m2, and its resistance is measured to be 5.0 W. What is the resistivity of the material at the temperature of the experiment? 3.5 A silver wire has a resistance of 2.1 W at 27.5 °C, and a resistance of 2.7 W at 100 °C. Determine the temperature coefficient of resistivity of silver. 3.6 A heating element using nichrome connected to a 230 V supply draws an initial current of 3.2 A which settles after a few seconds to a steady value of 2.8 A. What is the steady temperature of the heating element if the room temperature is 27.0 °C? Temperature coefficient of resistance of nichrome averaged over the temperature range involved is 1.70 × 10–4 °C–1. 3.7 Determine the current in each branch of the network shown in Fig. 3.20: FIGURE 3.20 3.8 A storage battery of emf 8.0 V and internal resistance 0.5 W is being charged by a 120 V dc supply using a series resistor of 15.5 W. What is the terminal voltage of the battery during charging? What is the purpose of having a series resistor in the charging circuit? 3.9 The number density of free electrons in a copper conductor estimated in Example 3.1 is 8.5 × 1028 m–3. How long does an electron take to drift from one end of a wire 3.0 m long to its other end? The area of cross-section of the wire is 2.0 × 10–6 m2 and it is carrying a current of 3.0 A. Reprint 2025-26 Chapter Four MOVING CHARGES AND MAGNETISM 4.1 INTRODUCTION Both Electricity and Magnetism have been known for more than 2000 years. However, it was only about 200 years ago, in 1820, that it was realised that they were intimately related. During a lecture demonstration in the summer of 1820, Danish physicist Hans Christian Oersted noticed that a current in a straight wire caused a noticeable deflection in a nearby magnetic compass needle. He investigated this phenomenon. He found that the alignment of the needle is tangential to an imaginary circle which has the straight wire as its centre and has its plane perpendicular to the wire. This situation is depicted in Fig.4.1(a). It is noticeable when the current is large and the needle sufficiently close to the wire so that the earth’s magnetic field may be ignored. Reversing the direction of the current reverses the orientation of the needle [Fig. 4.1(b)]. The deflection increases on increasing the current or bringing the needle closer to the wire. Iron filings sprinkled around the wire arrange themselves in concentric circles with the wire as the centre [Fig. 4.1(c)]. Oersted concluded that moving charges or currents produced a magnetic field in the surrounding space. Following this, there was intense experimentation. In 1864, the laws obeyed by electricity and magnetism were unified and formulated by Reprint 2025-26 Physics James Maxwell who then realised that light was electromagnetic waves. Radio waves were discovered by Hertz, and produced by J.C.Bose and G. Marconi by the end of the 19th century. A remarkable scientific and technological progress took place in the 20th century. This was due to our increased understanding of electromagnetism and the invention of devices for production, amplification, transmission and detection of electromagnetic waves. FIGURE 4.1 The magnetic field due to a straight long current-carrying wire. The wire is perpendicular to the plane of the paper. A ring of compass needles surrounds the wire. The orientation of the needles is shown when (a) the current emerges out of the plane of the paper, (b) the current moves into the plane of the paper. (c) The arrangement of iron filings around the wire. The darkened ends of the needle represent north poles. The effect of the earth’s magnetic field is neglected. In this chapter, we will see how magnetic field exerts forces on moving charged particles, like electrons, protons, and current-carrying wires. We shall also learn how currents produce magnetic fields. We shall see how particles can be accelerated to very high energies in a cyclotron. We shall study how currents and voltages are detected by a galvanometer.(1777–1851) In this and subsequent Chapter on magnetism, we adopt the following convention: A current or a field (electric or magnetic) emerging out of the plane of the paper is depicted by a dot (¤). A current or a field going into the plane of the paper is depicted by a cross ()*. Hans Christian Oersted Figures. 4.1(a) and 4.1(b) correspond to these twoOERSTED (1777–1851) Danish situations, respectively. physicist and chemist, professor at Copenhagen. 4.2 MAGNETIC FORCE He observed that a compass needle suffers a 4.2.1 Sources and fields deflection when placed Before we introduce the concept of a magnetic field B, weCHRISTIAN near a wire carrying an electric current. This shall recapitulate what we have learnt in Chapter 1 about discovery gave the first the electric field E. We have seen that the interaction empirical evidence of a between two charges can be considered in two stages.HANS connection between electric The charge Q, the source of the field, produces an electric and magnetic phenomena. field E, where * A dot appears like the tip of an arrow pointed at you, a cross is like the feathered 108 tail of an arrow moving away from you. Reprint 2025-26 Moving Charges and Magnetism E = Q ˆr / (4pe0)r2 (4.1) where ˆr is unit vector along r, and the field E is a vector field. A charge q interacts with this field and experiences a force F given by F = q E = q Q ˆr / (4pe0) r 2 (4.2) As pointed out in the Chapter 1, the field E is not just an artefact but has a physical role. It can convey energy and momentum and is not established instantaneously but takes finite time to propagate. The concept of a field was specially stressed by Faraday and was incorporated by Maxwell in his unification of electricity and magnetism. In addition to depending on each point in space, it can also vary with time, i.e., be a function of time. In our Hendrik Antoon Lorentz discussions in this chapter, we will assume that the fields (1853 – 1928) Dutch do not change with time. theoretical physicist, The field at a particular point can be due to one or professor at Leiden. He investigated themore charges. If there are more charges the fields add HENDRIK relationship between vectorially. You have already learnt in Chapter 1 that this electricity, magnetism, and is called the principle of superposition. Once the field is mechanics. In order to known, the force on a test charge is given by Eq. (4.2). explain the observed effect Just as static charges produce an electric field, the of magnetic fields on ANTOONcurrents or moving charges produce (in addition) a emitters of light (Zeeman magnetic field, denoted by B (r), again a vector field. It effect), he postulated the existence of electric chargeshas several basic properties identical to the electric field. in the atom, for which he It is defined at each point in space (and can in addition was awarded the Nobel Prize depend on time). Experimentally, it is found to obey the in 1902. He derived a set of LORENTZprinciple of superposition: the magnetic field of several transformation equations sources is the vector addition of magnetic field of each (known after him, as individual source. Lorentz transformation equations) by some tangled (1853 4.2.2 Magnetic Field, Lorentz Force mathematical arguments, – but he was not aware thatLet us suppose that there is a point charge q (moving these equations hinge on a with a velocity v and, located at r at a given time t) in new concept of space andpresence of both the electric field E (r) and the magnetic 1928) time. field B (r). The force on an electric charge q due to both of them can be written as F = q [ E (r) + v × B (r)] º Felectric +Fmagnetic (4.3) This force was given first by H.A. Lorentz based on the extensive experiments of Ampere and others. It is called the Lorentz force. You have already studied in detail the force due to the electric field. If we look at the interaction with the magnetic field, we find the following features. (i) It depends on q, v and B (charge of the particle, the velocity and the magnetic field). Force on a negative charge is opposite to that on a positive charge. (ii) The magnetic force q [ v × B ] includes a vector product of velocity 109 and magnetic field. The vector product makes the force due to magnetic Reprint 2025-26 Physics field vanish (become zero) if velocity and magnetic field are parallel or anti-parallel. The force acts in a (sideways) direction perpendicular to both the velocity and the magnetic field. Its direction is given by the screw rule or right hand rule for vector (or cross) product as illustrated in Fig. 4.2. (iii) The magnetic force is zero if charge is not moving (as then |v|= 0). Only a moving charge feels the magnetic force. The expression for the magnetic force helps us to define the unit of the magnetic field, if one FIGURE 4.2 The direction of the magnetic takes q, F and v, all to be unity in the force force acting on a charged particle. (a) The equation F = q [ v × B] =q v B sin q ˆn , where q is force on a positively charged particle with the angle between v and B [see Fig. 4.2 (a)]. The velocity v and making an angle q with the magnitude of magnetic field B is 1 SI unit, when magnetic field B is given by the right-hand the force acting on a unit charge (1 C), moving rule. (b) A moving charged particle q is perpendicular to B with a speed 1m/s, is one deflected in an opposite sense to –q in the newton. presence of magnetic field. Dimensionally, we have [B] = [F/qv] and the unit of B are Newton second / (coulomb metre). This unit is called tesla (T) named after Nikola Tesla (1856 – 1943). Tesla is a rather large unit. A smaller unit (non-SI) called gauss (=10–4 tesla) is also often used. The earth’s magnetic field is about 3.6 × 10–5 T. 4.2.3 Magnetic force on a current-carrying conductor We can extend the analysis for force due to magnetic field on a single moving charge to a straight rod carrying current. Consider a rod of a uniform cross-sectional area A and length l. We shall assume one kind of mobile carriers as in a conductor (here electrons). Let the number density of these mobile charge carriers in it be n. Then the total number of mobile charge carriers in it is nlA. For a steady current I in this conducting rod, we may assume that each mobile carrier has an average drift velocity vd (see Chapter 3). In the presence of an external magnetic field B, the force on these carriers is: F = (nlA)q vd ´ B where q is the value of the charge on a carrier. Now nq vd is the current density j and |(nq vd)|A is the current I (see Chapter 3 for the discussion of current and current density). Thus, F = [(nq vd )lA] × B = [ jAl ] ´ B = Il ´ B (4.4) where l is a vector of magnitude l, the length of the rod, and with a direction identical to the current I. Note that the current I is not a vector. In the last step leading to Eq. (4.4), we have transferred the vector sign from j to l. Equation (4.4) holds for a straight rod. In this equation, B is the external magnetic field. It is not the field produced by the current-carrying rod. If the wire has an arbitrary shape we can calculate the Lorentz force on it by considering it as a collection of linear strips dlj and summing F  Idl j × B j This summation can be converted to an integral in most cases. Reprint 2025-26 Moving Charges and Magnetism Example 4.1 A straight wire of mass 200 g and length 1.5 m carries a current of 2 A. It is suspended in mid-air by a uniform horizontal magnetic field B (Fig. 4.3). What is the magnitude of the magnetic field? FIGURE 4.3 Solution From Eq. (4.4), we find that there is an upward force F, of magnitude IlB,. For mid-air suspension, this must be balanced by the force due to gravity: m g = I lB m g B = I l Interactive Charged 0.2 × 9.8 = = 0.65 T 2 × 1.5 Note that it would have been sufficient to specify m/l, the mass per EXAMPLE particles unit length of the wire. The earth’s 4 × 10–5 T and we have ignored it. magnetic field is approximately 4.1 moving demonstration: in a Example 4.2 If the magnetic field is parallel to the positive y-axis and the charged particle is moving along the positive x-axis (Fig. 4.4), which way would the Lorentz force be for (a) an electron (negative magnetic charge), (b) a proton (positive charge). field. http://www.phys.hawaii.edu/~teb/optics/java/partmagn/index.html FIGURE 4.4 Solution The velocity v of particle is along the x-axis, while B, the magnetic field is along the y-axis, so v × B is along the z-axis (screw rule or right-hand thumb rule). So, (a) for electron it will be along –z EXAMPLE axis. (b) for a positive charge (proton) the force is along +z axis. 4.2 111 Reprint 2025-26 Physics 4.3 MOTION IN A MAGNETIC FIELD We will now consider, in greater detail, the motion of a charge moving in a magnetic field. We have learnt in Mechanics (see Class XI book, Chapter 5) that a force on a particle does work if the force has a component along (or opposed to) the direction of motion of the particle. In the case of motion of a charge in a magnetic field, the magnetic force is perpendicular to the velocity of the particle. So no work is done and no change in the magnitude of the velocity is produced (though the direction of momentum may be changed). [Notice that this is unlike the force due to an electric field, qE, which can have a component parallel (or antiparallel) to motion and thus can transfer energy in addition to momentum.] We shall consider motion of a charged particle in a uniform magnetic field. First consider the case of v perpendicular to B. The perpendicular force, q v × B, acts as a centripetal force and produces a circular motion perpendicular to the magnetic field. The particle will describe a circle if v and B are perpendicular to each other (Fig. 4.5). If velocity has a component along B, this component remains unchanged as the motion along the magnetic field will not be affected by the magnetic field. The motion in a plane perpendicular to B is as before a circular one, thereby producing a helical motion (Fig. 4.6). You have already learnt in earlier classes (See Class XI, Chapter 3) that if r is the radius of the circular path of a particle, then a force of m v2 / r, acts perpendicular to the path towards the centre of the circle, and is called the centripetal force. If the FIGURE 4.5 Circular motion velocity v is perpendicular to the magnetic field B, the magnetic force is perpendicular to both v and B and acts like a centripetal force. It has a magnitude q v B. Equating the two expressions for centripetal force, m v 2/r = q v B, which gives r = m v / qB (4.5) for the radius of the circle described by the charged particle. The larger the momentum, the larger is the radius and bigger the circle described. If w is the angular frequency, then v = w r. So, w = 2p n = q B/ m [4.6(a)] which is independent of the velocity or energy . Here n is the frequency of rotation. The independence of n from energy has important application in the design of a cyclotron. The time taken for one revolution is T= 2p/ w º 1/n. If there is a component of the velocity FIGURE 4.6 Helical motion parallel to the magnetic field (denoted by v||), 112 it will make the particle move along the field and the path of the Reprint 2025-26 Moving Charges and Magnetism particle would be a helical one (Fig. 4.6). The distance moved along the magnetic field in one rotation is called pitch p. Using Eq. [4.6 (a)], we have p = v||T = 2pm v|| / q B [4.6(b)] The radius of the circular component of motion is called the radius of the helix. Example 4.3 What is the radius of the path of an electron (mass 9 × 10-31 kg and charge 1.6 × 10–19 C) moving at a speed of 3 ×107 m/s in a magnetic field of 6 × 10–4 T perpendicular to it? What is its frequency? Calculate its energy in keV. ( 1 eV = 1.6 × 10–19 J). Solution Using Eq. (4.5) we find r = m v / (qB) = 9 ×10–31 kg × 3 × 107 m s–1 / ( 1.6 × 10–19 C × 6 × 10–4 T) = 28 × 10–2 m = 28 cm n = v / (2 pr) = 17×106 s–1 = 17×106 Hz =17 MHz. 2 EXAMPLE E = (½ )mv = (½ ) 9 × 10–31 kg × 9 × 1014 m2/s2 = 40.5 ×10–17 J ≈ 4×10–16 J = 2.5 keV. 4.3

6.4 FARADAY’S LAW OF INDUCTION From the experimental observations, Faraday arrived at a conclusion that an emf is induced in a coil when magnetic flux through the coil changes with time. Experimental observations discussed in Section 6.2 can be explained using this concept. The motion of a magnet towards or away from coil C1 in Experiment 6.1 and moving a current-carrying coil C2 towards or away from coil C1 in Experiment 6.2, change the magnetic flux associated with coil C1. The change in magnetic flux induces emf in coil C1. It was this induced emf which caused electric current to flow in coil C1 and through the galvanometer. A FIGURE 6.5 Magnetic field Bi plausible explanation for the observations of Experiment 6.3 is at the ith area element. dAi represents area vector of theas follows: When the tapping key K is pressed, the current in ith area element. coil C2 (and the resulting magnetic field) rises from zero to a maximum value in a short time. Consequently, the magnetic flux through the neighbouring coil C1 also increases. It is the change in magnetic flux through coil C1 that produces an induced emf in coil C1. When the key is held pressed, current in coil C2 is constant. Therefore, there is no change in the magnetic flux through coil C1 and the current in coil C1 drops to zero. When the key is released, the current in C2 and the resulting magnetic field decreases from the maximum value to zero in a short time. This results in a decrease in magnetic flux through coil C1 and hence again induces an electric current in coil C1*. The common point in all these observations is that the time rate of change of magnetic flux through a circuit induces emf in it. Faraday stated experimental observations in the form of a law called Faraday’s law of electromagnetic induction. The law is stated below. * Note that sensitive electrical instruments in the vicinity of an electromagnet can be damaged due to the induced emfs (and the resulting currents) when the electromagnet is turned on or off. 157 Reprint 2025-26 Physics The magnitude of the induced emf in a circuit is equal to the time rate of change of magnetic flux through the circuit. Mathematically, the induced emf is given by dΦB ε = – (6.3) d t The negative sign indicates the direction of e and hence the direction of current in a closed loop. This will be discussed in detail in the next section. In the case of a closely wound coil of N turns, change of flux associated with each turn, is the same. Therefore, Michael Faraday [1791– the expression for the total induced emf is given by 1867] Faraday made numerous contributions to dΦB ε = – N (6.4)(1791–1867) science, viz., the discovery d t of electromagnetic induction, the laws of The induced emf can be increased by increasing the electrolysis, benzene, and number of turns N of a closed coil. the fact that the plane of From Eqs. (6.1) and (6.2), we see that the flux can be polarisation is rotated in an varied by changing any one or more of the terms B, A andFARADAY electric field. He is also credited with the invention q. In Experiments 6.1 and 6.2 in Section 6.2, the flux is of the electric motor, the changed by varying B. The flux can also be altered by electric generator and the changing the shape of a coil (that is, by shrinking it or transformer. He is widely stretching it) in a magnetic field, or rotating a coil in a regarded as the greatest magnetic field such that the angle q between B and AMICHAEL experimental scientist of changes. In these cases too, an emf is induced in the the nineteenth century. respective coils. Example 6.1 Consider Experiment 6.2. (a) What would you do to obtain a large deflection of the galvanometer? (b) How would you demonstrate the presence of an induced current in the absence of a galvanometer? Solution (a) To obtain a large deflection, one or more of the following steps can be taken: (i) Use a rod made of soft iron inside the coil C2, (ii) Connect the coil to a powerful battery, and (iii) Move the arrangement rapidly towards the test coil C1. (b) Replace the galvanometer by a small bulb, the kind one finds in a 6.1 small torch light. The relative motion between the two coils will cause the bulb to glow and thus demonstrate the presence of an induced current. In experimental physics one must learn to innovate. Michael Faraday who is ranked as one of the best experimentalists ever, was legendary EXAMPLE for his innovative skills. 6.2 Example 6.2 A square loop of side 10 cm and resistance 0.5 W is placed vertically in the east-west plane. A uniform magnetic field of 0.10 T is set up across the plane in the north-east direction. The magnetic field is decreased to zero in 0.70 s at a steady rate. Determine EXAMPLE the magnitudes of induced emf and current during this time-interval.158 Reprint 2025-26 Electromagnetic Induction Solution The angle q made by the area vector of the coil with the magnetic field is 45°. From Eq. (6.1), the initial magnetic flux is F = BA cos q 0.1 × 10 –2 = Wb 2 Final flux, Fmin = 0 The change in flux is brought about in 0.70 s. From Eq. (6.3), the magnitude of the induced emf is given by –3 ∆ΦB (Φ – 0 ) 10 ε = = = = 1.0 mV ∆ t ∆ t 2 × 0.7 And the magnitude of the current is ε 10 –3 V I = = = 2 mA R 0.5 Ω Note that the earth’s magnetic field also produces a flux through the EXAMPLE loop. But it is a steady field (which does not change within the time span of the experiment) and hence does not induce any emf. 6.2 Example 6.3 A circular coil of radius 10 cm, 500 turns and resistance 2 W is placed with its plane perpendicular to the horizontal component of the earth’s magnetic field. It is rotated about its vertical diameter through 180° in 0.25 s. Estimate the magnitudes of the emf and current induced in the coil. Horizontal component of the earth’s magnetic field at the place is 3.0 × 10–5 T. Solution Initial flux through the coil, FB (initial) = BA cos q = 3.0 × 10–5 × (p ×10–2) × cos 0° = 3p × 10–7 Wb Final flux after the rotation, FB (final) = 3.0 × 10–5 × (p ×10–2) × cos 180° = –3p × 10–7 Wb Therefore, estimated value of the induced emf is, ∆Φ ε = N ∆t = 500 × (6p × 10–7)/0.25 = 3.8 × 10–3 V I = e/R = 1.9 × 10–3 A Note that the magnitudes of e and I are the estimated values. Their EXAMPLE instantaneous values are different and depend upon the speed of rotation at the particular instant. 6.3 159 Reprint 2025-26 Physics 6.5 LENZ’S LAW AND CONSERVATION OF ENERGY In 1834, German physicist Heinrich Friedrich Lenz (1804-1865) deduced a rule, known as Lenz’s law which gives the polarity of the induced emf in a clear and concise fashion. The statement of the law is: The polarity of induced emf is such that it tends to produce a current which opposes the change in magnetic flux that produced it. The negative sign shown in Eq. (6.3) represents this effect. We can understand Lenz’s law by examining Experiment 6.1 in Section 6.2.1. In Fig. 6.1, we see that the North-pole of a bar magnet is being pushed towards the closed coil. As the North-pole of the bar magnet moves towards the coil, the magnetic flux through the coil increases. Hence current is induced in the coil in such a direction that it opposes the increase in flux. This is possible only if the current in the coil is in a counter-clockwise direction with respect to an observer situated on the side of the magnet. Note that magnetic moment associated with this current has North polarity towards the North-pole of the approaching magnet. Similarly, if the North- pole of the magnet is being withdrawn from the coil, the magnetic flux through the coil will decrease. To counter this decrease in magnetic flux, the induced current in the coil flows in clockwise direction and its South- pole faces the receding North-pole of the bar magnet. This would result in an attractive force which opposes the motion of the magnet and the corresponding decrease in flux. What will happen if an open circuit is used in place of the closed loop in the above example? In this case too, an emf is induced across the open ends of the circuit. The direction of the induced emf can be found using Lenz’s law. Consider Figs. 6.6 (a) and (b). They provide an easier way to understand the direction of induced currents. Note that the direction shown by and indicate the directions of the induced currents. A little reflection on this matter should convince us on the correctness of Lenz’s law. Suppose that the induced current was in the direction opposite to the one depicted in Fig. 6.6(a). In that case, the South-pole due to the induced current will face the approaching North-pole of the magnet. The bar magnet will then be attracted towards the coil at an ever increasing acceleration. A gentle push on the magnet will initiate the process and its velocity and kinetic energy will continuously increase without expending any energy. If this can happen, one could construct a perpetual-motion machine by a suitable arrangement. This violates the law of conservation of energy and hence can not happen. FIGURE 6.6 Now consider the correct case shown in Fig. 6.6(a). In this situation, Illustration of the bar magnet experiences a repulsive force due to the induced Lenz’s law. current. Therefore, a person has to do work in moving the magnet. Where does the energy spent by the person go? This energy is 160 dissipated by Joule heating produced by the induced current. Reprint 2025-26 Electromagnetic Induction Example 6.4 Figure 6.7 shows planar loops of different shapes moving out of or into a region of a magnetic field which is directed normal to the plane of the loop away from the reader. Determine the direction of induced current in each loop using Lenz’s law. FIGURE 6.7 Solution (i) The magnetic flux through the rectangular loop abcd increases, due to the motion of the loop into the region of magnetic field, The induced current must flow along the path bcdab so that it opposes the increasing flux. (ii) Due to the outward motion, magnetic flux through the triangular loop abc decreases due to which the induced current flows along bacb, so as to oppose the change in flux. (iii) As the magnetic flux decreases due to motion of the irregular shaped loop abcd out of the region of magnetic field, the induced current flows along cdabc, so as to oppose change in flux. EXAMPLE Note that there are no induced current as long as the loops are 6.4 completely inside or outside the region of the magnetic field. Example 6.5 (a) A closed loop is held stationary in the magnetic field between the north and south poles of two permanent magnets held fixed. Can we hope to generate current in the loop by using very strong magnets? (b) A closed loop moves normal to the constant electric field between the plates of a large capacitor. Is a current induced in the loop (i) when it is wholly inside the region between the capacitor plates (ii) when it is partially outside the plates of the capacitor? The electric field is normal to the plane of the loop. (c) A rectangular loop and a circular loop are moving out of a uniform magnetic field region (Fig. 6.8) to a field-free region with a constant velocity v. In which loop do you expect the induced emf to be EXAMPLE during constant the passage out of the field region? The field is 6.5 normal to the loops. 161 Reprint 2025-26 Physics FIGURE 6.8 (d) Predict the polarity of the capacitor in the situation described by Fig. 6.9. FIGURE 6.9 Solution (a) No. However strong the magnet may be, current can be induced only by changing the magnetic flux through the loop. (b) No current is induced in either case. Current can not be induced by changing the electric flux. 6.5 (c) The induced emf is expected to be constant only in the case of the rectangular loop. In the case of circular loop, the rate of change of area of the loop during its passage out of the field region is not constant, hence induced emf will vary accordingly. (d) The polarity of plate ‘A’ will be positive with respect to plate ‘B’ in EXAMPLE the capacitor. 6.6 MOTIONAL ELECTROMOTIVE FORCE Let us consider a straight conductor moving in a uniform and time- independent magnetic field. Figure 6.10 shows a rectangular conductor PQRS in which the conductor PQ is free to move. The rod PQ is moved towards the left with a constant velocity v as shown in the figure. Assume that there is no loss of energy due to friction. PQRS forms a closed circuit enclosing an area that changes as PQ moves. It is placed in a uniform magnetic field B which is perpendicular to the plane of this system. If the length RQ = x and RS = l, the magnetic flux FB enclosed by the loop PQRS will be FB = Blx Since x is changing with time, the rate of change of flux FB will induce an emf given by: FIGURE 6.10 The arm PQ is moved to the left – dΦB d side, thus decreasing the area of the ε= = – ( Blx ) d t d t rectangular loop. This movement induces a current I as shown. d x 162 = – Bl = Blv (6.5) d t Reprint 2025-26 Electromagnetic Induction where we have used dx/dt = –v which is the speed of the conductor PQ. The induced emf Blv is called motional emf. Thus, we are able to produce induced emf by moving a conductor instead of varying the magnetic field, that is, by changing the magnetic flux enclosed by the circuit. It is also possible to explain the motional emf expression in Eq. (6.5) by invoking the Lorentz force acting on the free charge carriers of conductor PQ. Consider any arbitrary charge q in the conductor PQ. When the rod moves with speed v, the charge will also be moving with speed v in the magnetic field B. The Lorentz force on this charge is qvB in magnitude, and its direction is towards Q. All charges experience the same force, in magnitude and direction, irrespective of their position in the rod PQ. The work done in moving the charge from P to Q is, W = qvBl Since emf is the work done per unit charge, W ε = q = Blv This equation gives emf induced across the rod PQ and is identical to Eq. (6.5). We stress that our presentation is not wholly rigorous. But it does help us to understand the basis of Faraday’s law when the conductor is moving in a uniform and time-independent magnetic field. On the other hand, it is not obvious how an emf is induced when a conductor is stationary and the magnetic field is changing – a fact which Faraday verified by numerous experiments. In the case of a stationary conductor, the force on its charges is given by F = q (E + v ´ B) = qE (6.6) since v = 0. Thus, any force on the charge must arise from the electric field term E alone. Therefore, to explain the existence of induced emf or induced current, we must assume that a time-varying magnetic field generates an electric field. However, we hasten to add that electric fields produced by static electric charges have properties different from those produced by time-varying magnetic fields. In Chapter 4, we learnt that charges in motion (current) can exert force/torque on a stationary magnet. Conversely, a bar magnet in motion (or more generally, a changing magnetic field) can exert a force on the stationary charge. This is the fundamental significance of the Faraday’s discovery. Electricity and magnetism are related. Example 6.6 A metallic rod of 1 m length is rotated with a frequency of 50 rev/s, with one end hinged at the centre and the other end at the circumference of a circular metallic ring of radius 1 m, about an axis passing through the centre and perpendicular to the plane of the ring (Fig. 6.11). A constant and uniform magnetic field of 1 T parallel to the EXAMPLE axis is present everywhere. What is the emf between the centre and the metallic ring? 6.6 163 Reprint 2025-26 Physics FIGURE 6.11 Solution Method I As the rod is rotated, free electrons in the rod move towards the outer end due to Lorentz force and get distributed over the ring. Thus, the resulting separation of charges produces an emf across the ends of the rod. At a certain value of emf, there is no more flow of electrons and a steady state is reached. Using Eq. (6.5), the magnitude of the emf generated across a length dr of the rod as it moves at right angles to the magnetic field is given by dε = Bv dr . Hence, R R B ωR 2 ωr d r = Bv d r = ∫B ε =∫ d ε = ∫ 2 0 0 Note that we have used v = w r. This gives 1 2 e = × 1.0 × 2 π × 50 × (1 ) 2 = 157 V Method II To calculate the emf, we can imagine a closed loop OPQ in which point O and P are connected with a resistor R and OQ is the rotating rod. The potential difference across the resistor is then equal to the induced emf and equals B × (rate of change of area of loop). If q is the angle between the rod and the radius of the circle at P at time t, the area of the sector OPQ is given by 2 θ 1 2 π R × = R θ 2 π 2 where R is the radius of the circle. Hence, the induced emf is d  1  1 2 dθ BωR 2 e = B × R 2θ = BR = d t  2  2 d t 2 6.6 dθ [Note: = ω = 2 π ν] dt This expression is identical to the expression obtained by Method I EXAMPLE and we get the same value of e. Reprint 2025-26 Electromagnetic Induction Example 6.7 A wheel with 10 metallic spokes each 0.5 m long is rotated with a speed of 120 rev/min in a plane normal to the horizontal component of earth’s magnetic field HE at a place. If HE = 0.4 G at the place, what is the induced emf between the axle and the rim of the wheel? Note that 1 G = 10–4 T. Solution Induced emf = (1/2) ω B R2 = (1/2) × 4π × 0.4 × 10–4 × (0.5)2 = 6.28 × 10–5 V EXAMPLE The number of spokes is immaterial because the emf’s across the 6.7 spokes are in parallel.